ENTRY AND START SYSTEM All Door Entry Lock/Unlock Functions do not Operate, but Wireless Functions Operate

DESCRIPTION

When the wireless operation can be used to lock and unlock the doors, the communication line between the door control receiver and certification ECU is normal. When the entry operation does not operate, one of the following may be the cause: 1) entry cancel function is set through customization; 2) malfunction in entry and start system communication line (electrical key transmitter and vehicle); or 3) wave interference.

INSPECTION PROCEDURE

PROCEDURE


  1. READ VALUE USING INTELLIGENT TESTER (AUTO ENTRY CANCEL SW)


    1. Using the intelligent tester, read the Data List.

      Entry & Start (Certification ECU)
      Tester Display Measurement Item/Display Normal Condition Diagnostic Note
      Auto Entry Cancel SW Entry function cancel / ON or OFF Mode status is displayed -
      Result
      Result Proceed to
      Entry function is OFF A
      Entry function is ON B

    B

    PERFORM CANCELLATION OF ENTRY KEY CANCEL FUNCTION Click here

    A

  2. CHECK WAVE ENVIRONMENT


    1. Move the electrical key transmitter as described below and perform the operation inspection.

      Tech Tips


      • When the electrical key transmitter is brought near the door outside handle or electrical key antenna, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

      • The transmitting wave of the wireless function and entry function are the same, but the wave logic is different. As a result, it is possible that only the wireless function or only the entry function is affected by wave interference.

    2. A01GIUDE02

      Bring the electrical key transmitter near the driver door outside handle, and perform a driver door entry lock and unlock operation check.

      Note

      If the key is brought within 0.2 m (0.6 ft.) of the door handle, communication is not possible.

      Tech Tips

      On opposite side for RHD vehicle.

    3. A01GI1IE01

      Bring the electrical key transmitter near the front passenger door outside handle, and perform a front passenger door entry lock and unlock operation check.

      Note

      If the key is brought within 0.2 m (0.6 ft.) of the door handle, communication is not possible.

      Tech Tips

      On opposite side for RHD vehicle.

    4. A01GHOTE01

      Bring the electrical key transmitter near the rear left. door outside handle, and perform a rear left. door entry lock and unlock operation check.

      Note

      If the key is brought within 0.2 m (0.6 ft.) of the door handle, communication is not possible.

    5. A01GNWHE01

      Bring the electrical key transmitter near the rear right door outside handle, and perform a rear right door entry lock and unlock operation check.

      Note

      If the key is brought within 0.2 m (0.6 ft.) of the door handle, communication is not possible.

    6. Bring the electrical key transmitter near the indoor electrical key oscillator (in center console), and perform an engine start check.

      Note

      If the key is brought within 0.2 m (0.6 ft.) of the center console, communication is not possible.

    7. Bring the electrical key transmitter near the indoor electrical key oscillator (in rear seat cushion), and perform an engine start check.

      Note

      If the key is brought within 0.2 m (0.6 ft.) of the rear seat cushion, communication is not possible.

    8. A01GLJIE02

      Bring the electrical key transmitter near the electrical key antenna (in rear bumper), and perform an entry luggage compartment open function check.

      Note

      If the key is brought within 0.2 m (0.6 ft.) of the rear bumper, communication is not possible.

      Tech Tips

      If the inspection result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

      Result
      Result Proceed to
      All operation checks fail A
      Some operation checks are normal B

    B

    AFFECTED BY WAVE INTERFERENCE

    A

  3. KEY DIAGNOSTIC MODE


    1. A01GIUDE07

      Diagnostic mode inspection (driver door outside oscillator)

      Tech Tips

      On opposite side for RHD vehicle.


      1. Connect the intelligent tester to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus:


        1. Intelligent tester - Select: Body / Entry & Start / Key Communication Check / Overhead + Driver Side /

      5. When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.

    2. A01GI1IE02

      Diagnostic mode inspection (front passenger door outside oscillator)

      Tech Tips

      On opposite side for RHD vehicle.


      1. Connect the intelligent tester to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus:


        1. Intelligent tester - Select: Body / Entry & Start / Key Communication Check / Overhead + Passenger Side /

      5. When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.

    3. A01GHOTE02

      Diagnostic mode inspection (rear door outside oscillator)

      Tech Tips

      On opposite side for RHD vehicle.


      1. Connect the intelligent tester to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus:


        1. Intelligent tester - Select: Body / Entry & Start / Key Communication Check / Overhead + Driver Side Rear /

      5. When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.

    4. A01GNWHE02

      Diagnostic mode inspection (rear door outside oscillator)

      Tech Tips

      On opposite side for RHD vehicle.


      1. Connect the intelligent tester to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus:


        1. Intelligent tester - Select: Body / Entry & Start / Key Communication Check / Overhead + Passenger Side Rear /

      5. When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.

    5. A01GL0RE01

      Diagnostic mode inspection (front inside oscillator)


      1. Connect the intelligent tester to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus:


        1. Intelligent tester - Select: Body / Entry & Start / Key Communication Check / Overhead + Front Room /

      5. When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.

    6. A01GJSFE01

      Diagnostic mode inspection (rear inside oscillator)


      1. Connect the intelligent tester to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus:


        1. Intelligent tester - Select: Body / Entry & Start / Key Communication Check / Overhead + Rear Room /

      5. When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.

    7. A01GLJIE06

      Diagnostic mode inspection (luggage compartment antenna)


      1. Connect the intelligent tester to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus:


        1. Intelligent tester - Select: Body / Entry & Start / Key Communication Check / Overhead + Luggage /

      5. When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.

        Result
        Result Proceed to
        All diagnostic mode inspections fail A
        Some diagnostic mode inspections fail (door) B
        Some diagnostic mode inspections fail (interior) C
        Some diagnostic mode inspections fail (luggage compartment) D
        All diagnostic mode inspections are normal E

    B

    GO TO DTC OF OTHER COMPONENTS (PROCEED TO PROBLEM SYMPTOM FLOWCHART FOR EACH DOOR)

    C

    GO TO OTHER FLOWCHART Click here

    D

    GO TO OTHER FLOWCHART Click here

    E

    REPLACE CERTIFICATION ECU

    A

  4. REPLACE ELECTRICAL KEY TRANSMITTER


    1. Replace the electrical key transmitter with a new one and perform the registration procedure.


    NEXT

  5. CHECK OPERATION


    1. Check the operation of the entry lock function.

      OK
      Operates normally

    NG

    REPLACE CERTIFICATION ECU

    OK

    END