LIGHTING SYSTEM, Diagnostic DTC:B2410, B2411

DTC Code DTC Name
B2410 Headlight Swivel Motor LH Communication Malfunction
B2411 Headlight Swivel Motor RH Communication Malfunction

DESCRIPTION

These DTCs are output when the AFS ECU detected errors in its own communications with the headlight (headlight swivel motor).

DTC Code DTC Detection Condition Trouble Area
B2410 AFS ECU detected errors in its own communications with headlight swivel motor LH

  • AFS ECU

  • Headlight assembly LH

  • Headlight swivel motor LH

  • Harness or connector
B2411 AFS ECU detected errors in its own communications with headlight swivel motor RH

  • AFS ECU

  • Headlight assembly RH

  • Headlight swivel motor RH

  • Harness or connector

WIRING DIAGRAM

A01GMPQE07

INSPECTION PROCEDURE

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. CHECK FOR DTC


    1. Clear the DTC Click here.

    2. Check for DTC Click here.

      OK
      DTC B2410 or B2411 output does not occur

    NG

    CHECK HARNESS AND CONNECTOR (AFS ECU - BATTERY AND BODY GROUND) Click here

    OK

    USE SIMULATION METHOD TO CHECK Click here

  2. CHECK HARNESS AND CONNECTOR (AFS ECU - BATTERY AND BODY GROUND)

    A01GJVFE45

    1. Disconnect the A37 AFS ECU connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      A37-14 (IGS) - Body ground Engine switch on (IG) 11 to 14 V
      A37-15 (IG) - Body ground Engine switch on (IG) 11 to 14 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A37-22 (E1) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (AFS ECU - HEADLIGHT)

    A01GKKFE05

    1. Disconnect the A37 AFS ECU connector.

    2. Disconnect the B1*1 or B11*2 headlight connector.


      • *1: for LH

      • *2: for RH

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LH
      Tester Connection Condition Specified Condition
      A37-1 (SMBL) - B1-13 (LHB1) Always Below 1 Ω
      A37-29 (SML) - B1-23 (SML) Always Below 1 Ω
      A37-27 (LH-) - B1-22 (LH E) Always Below 1 Ω
      A37-1 (SMBL) - Body ground Always 10 kΩ or higher
      A37-29 (SML) - Body ground Always 10 kΩ or higher
      A37-27 (LH-) - Body ground Always 10 kΩ or higher
      for RH
      Tester Connection Condition Specified Condition
      A37-2 (SMBR) - B11-13 (RHB1) Always Below 1 Ω
      A37-10 (SMR) - B11-23 (SMR) Always Below 1 Ω
      A37-28 (RH-) - B11-22 (RH E) Always Below 1 Ω
      A37-2 (SMBR) - Body ground Always 10 kΩ or higher
      A37-10 (SMR) - Body ground Always 10 kΩ or higher
      A37-28 (RH-) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT HEADLIGHT ASSEMBLY

    A01GJTGE06

    1. for HID Headlight


      1. Remove the headlight Click here.

    2. for LED Headlight


      1. Remove the headlight Click here.

    3. for HID Headlight


      1. Disconnect the headlight swivel motor connector Click here.

    4. for LED Headlight


      1. Disconnect the headlight swivel motor connector Click here.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LH
      Tester Connection Condition Specified Condition
      13 (LHB1) - 1 Always Below 1 Ω
      23 (SML) - 2 Always Below 1 Ω
      22 (LH E) - 3 Always Below 1 Ω
      for RH
      Tester Connection Condition Specified Condition
      13 (RHB1) - 1 Always Below 1 Ω
      23 (SMR) - 2 Always Below 1 Ω
      22 (RH E) - 3 Always Below 1 Ω
      Result
      Result Proceed to
      OK A
      NG (for HID Headlight) B
      NG (for LED Headlight) C

    B

    REPLACE HEADLIGHT ASSEMBLY Click here

    C

    REPLACE HEADLIGHT ASSEMBLY Click here

    A

  5. CHECK HEADLIGHT SWIVEL MOTOR


    1. for HID Headlight


      1. Temporarily replace the headlight swivel motor with a new or normally functioning one Click here.

    2. for LED Headlight


      1. Temporarily replace the headlight swivel motor with a new or normally functioning one Click here.

    3. Check for DTC Click here.

      OK
      DTC B2410 or B2411 output does not occur

    NG

    REPLACE AFS ECU Click here

    OK

    END (HEADLIGHT SWIVEL MOTOR WAS DEFECTIVE)