DRIVER MONITOR ECU (for LHD) INSTALLATION

Tech Tips

A bolt without a torque specification is shown in the standard bolt chart Click here.


  1. INSTALL DRIVER MONITOR ECU ASSEMBLY


    1. Install the driver monitor ECU assembly with the nut.

    2. Install the ECU unit with the 2 nuts.

      Torque:
      8.5 N*m  { 86 kgf*cm, 75 in.*lbf }

    3. Connect the 3 connectors.

  2. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01GMFB

      Connect the airbag connector.

      Note

      When connecting airbag connector, take care not to damage the airbag wire harness.

    4. Push in the lock to connect the airbag connector.

    5. Attach the claw to connect the hood lock control lever sub-assembly to the driver side knee airbag assembly.

    6. Attach the clip to install the driver side knee airbag assembly.

    7. Install the 4 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      Confirm that the driver side knee airbag assembly is installed securely without any excessive gaps and is not protruding outward.

  3. INSTALL NO. 1 INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY


    1. Attach the 5 clips to install the instrument panel safety pad sub-assembly.

    2. Install the 2 bolts <E>.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

    3. Install the 8 bolts <A> and nut <F>.

      A01GNJAE01
      Text in Illustration
      *1 Bolt <A> *2 Bolt <E>
      *3 Nut <F> - -

    4. Attach the 2 claws to connect the cooler thermistor.

    5. Connect each connector and each wire harness clamp.

  4. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

    A01GKF1

    1. Connect each connector and each wire harness clamp.

    2. Attach the 2 claws to connect the DLC3.

    3. Attach the 2 claws to install the No. 1 instrument panel under cover sub-assembly.

    4. Install the 2 screws.

  5. INSTALL INSTRUMENT PANEL ORNAMENT

    A01GKTP

    1. Connect the connector.

    2. Attach the 4 clips to install the instrument panel ornament.

  6. INSTALL INSTRUMENT SIDE PANEL LH

    A01GIB5

    1. Attach the 6 clips to install the instrument side panel LH.

  7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  8. INSTALL COWL TOP VENTILATOR LOUVER RH


    1. A01GM4S

      for LHD:

      Install the 6 clips and cowl top ventilator louver RH.

      Note

      If the cowl top ventilator louver RH is not properly installed, water may leak into the engine room and cause malfunctions. Therefore, make sure the cowl top ventilator louver RH is installed properly.

    2. A01GI9P

      for RHD:

      Install the 6 clips and cowl top ventilator louver LH.

      Note

      If the cowl top ventilator louver LH is not properly installed, water may leak into the engine room and cause malfunctions. Therefore, make sure the cowl top ventilator louver LH is installed properly.

  9. CHECK SRS WARNING LIGHT

    Click here