STEERING COLUMN ASSEMBLY (for AWD with VGRS) INSTALLATION


  1. INSTALL STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR)


    1. Install the steering column with the 4 nuts.

      Torque:
      26 N*m  { 260 kgf*cm, 19 ft.*lbf }

    2. Connect the connectors and wire harness clamps to the steering column.

  2. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY


    1. Install the clamp to the steering column hole cover sub-assembly.

    2. A01GLV7E02
      Text in Illustration
      *a Matchmark

      Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering column.

    3. Install the bolt.

      Torque:
      35 N*m  { 360 kgf*cm, 26 ft.*lbf }
    4. A01GKUZE02
      Text in Illustration
      *a Matchmark

      Align the matchmarks on the No. 2 steering intermediate shaft assembly and power steering link.

    5. Install the bolt.

      Torque:
      35 N*m  { 360 kgf*cm, 26 ft.*lbf }

  3. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

  4. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY


    1. Attach the 2 claws to install the air duct.

    2. Install the bolt.

      Torque:
      9.8 N*m  { 100 kgf*cm, 87 in.*lbf }

    3. Attach the 2 claws and install the wiring harness protector.

  5. INSTALL NO. 1 LOWER INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  6. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


    1. Install the turn signal switch assembly with spiral cable to the steering column with the clamp.

    2. Connect the connectors to the turn signal switch assembly with spiral cable.

  7. INSTALL STEERING COLUMN COVER (w/o Driver Monitor Camera)


    1. Attach the claw to install the steering column cover upper.

    2. Attach the 4 clips to install the steering column cover upper onto the instrument panel cluster finish panel.

    3. Attach the 2 claws to install the steering column cover lower.

      Note

      Do not damage the tilt and telescopic switch.

    4. Install the 3 screws.

  8. INSTALL STEERING COLUMN COVER (w/ Driver Monitor Camera)


    1. Connect the driver monitor connector.

    2. Attach the claw and install the steering column cover upper.

    3. Attach the 4 clips to install the steering column cover upper onto the instrument panel cluster finish panel.

    4. Attach the 2 claws to install the steering column cover lower.

      Note

      Do not damage the tilt and telescopic switch.

    5. Install the 3 screws.

  9. ADJUST SPIRAL CABLE SUB-ASSEMBLY

    Note

    Do not adjust the spiral cable sub-assembly with sensor with the battery connected and the engine switch on (IG).


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01GNO3

      Rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

      CAUTION:

      Do not turn the spiral cable sub-assembly using the airbag wire harness.

    4. A01GLREE01
      Text in Illustration
      *A w/o Steering Heater
      *B w/ Steering Heater
      *a Alignment Mark

      Rotate the spiral cable sub-assembly clockwise approximately 2.5 turns to align the marks.

      CAUTION:

      Do not turn the spiral cable sub-assembly using the airbag wire harness.

      Tech Tips

      The spiral cable sub-assembly will rotate approximately 2.5 turns to both the left and right from the center.

  10. INSTALL STEERING WHEEL ASSEMBLY

    Click here

  11. INSPECT STEERING WHEEL CENTER POINT

  12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    Reset the AUTO TILT AWAY function setting to the previous condition by changing the customize parameter Click here.

  13. INSTALL COWL TOP VENTILATOR LOUVER


    1. A01GM4S

      for LHD:

      Install the 6 clips and cowl top ventilator louver RH.

      Note

      If the cowl top ventilator louver RH is not properly installed, water may leak into the engine room and cause malfunctions. Therefore, make sure the cowl top ventilator louver RH is installed properly.

    2. A01GI9P

      for RHD:

      Install the 6 clips and cowl top ventilator louver LH.

      Note

      If the cowl top ventilator louver LH is not properly installed, water may leak into the engine room and cause malfunctions. Therefore, make sure the cowl top ventilator louver LH is installed properly.

  14. CHECK SRS WARNING LIGHT

    Click here.

  15. PERFORM INITIALIZATION

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.