PARKING BRAKE ASSEMBLY REASSEMBLY

Tech Tips


  • Use the same procedures for the LH side and RH side.


  • The procedures listed below are for the LH side.

CAUTION:

While the battery is connected, even if the engine switch is off, the brake control system activates when the brake pedal is depressed with the door courtesy switch on. Therefore during servicing of the brake system components, do not operate the brake pedal and open/close the doors while the battery is connected.


  1. INSTALL PARKING BRAKE ANCHOR BLOCK SUB-ASSEMBLY


    1. A01GI3A

      Install the parking brake anchor block and cable support bracket with the 2 nuts.

      Torque:
      76 N*m  { 775 kgf*cm, 56 ft.*lbf }

    2. Install the rear axle hub and bearing Click here.

  2. APPLY HIGH TEMPERATURE GREASE


    1. Apply a thin layer of high temperature grease to the area where the parking brake plate contacts the parking brake shoe Click here.

  3. INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY


    1. A01GJ7HE01

      Using SST, install the No. 2 parking brake shoe with the No. 2 shoe hold down spring cup, No. 2 compression spring and No. 1 shoe hold down spring pin.

      SST
      09718-00010

      Tech Tips

      Use the service hole to retain the No. 1 shoe hold down spring pin with your finger.

  4. INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY


    1. A01GNRQE01

      Using SST, install the No. 1 parking brake shoe with the No. 1 shoe hold down spring cup, No. 1 compression spring and No. 1 shoe hold down spring pin.

      SST
      09718-00010

      Tech Tips

      Use the service hole to retain the No. 1 shoe hold down spring pin with your finger.

  5. INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET


    1. A01GO05E05
      Text in Illustration
      *1 High-temperature grease

      Apply high-temperature grease to the thread and all joining areas of the parking brake shoe adjusting screw set.

    2. A01GMS8

      Install the parking brake shoe adjusting screw set.

  6. INSTALL NO. 2 PARKING BRAKE SHOE RETURN TENSION SPRING


    1. A01GKAW

      Install the No. 2 parking brake shoe return spring.

  7. INSTALL PARKING BRAKE SHOE LEVER


    1. A01GN8PE07
      Text in Illustration
      *A for LH
      *B for RH
      *1 High-temperature grease
      *2 Parking Brake Anchor Block

      Apply a thin layer of high temperature grease to the area where the parking brake shoe lever contacts the parking brake anchor block.

    2. Install the parking brake shoe lever to the parking brake cable.

      Note

      Take care to install the correct parking brake shoe lever because the direction of the pin is different between the left and right.

    3. A01GJZ0E03
      Text in Illustration
      *1 Inner Cable
      *2 Shoe Lever

      Check that the parking brake inner cable and parking brake shoe lever are securely connected by trying to pull them apart.

    4. A01GJVQ

      Install the parking brake cable to the support bracket with the 2 nuts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
    5. A01GJSI

      With the vehicle on the ground, check that the gap between the parking brake cable and drive shaft, and the gap between the parking brake cable and shaft boot are 10 mm (0.394 in.) or more.

      Tech Tips

      Make sure that the cable is not twisted.

  8. INSTALL NO. 1 PARKING BRAKE SHOE RETURN TENSION SPRING


    1. A01GKV5

      Install the No. 1 parking brake shoe return spring.

  9. CHECK PARKING BRAKE INSTALLATION


    1. Make sure that all the parts are installed properly.

      If necessary, reinstall the parts properly.

      A01GK8GE06
      Text in Illustration
      *A for LH Side *B for RH Side
      A01GKOV Front - -

  10. INSTALL REAR DISC


    1. Align the matchmarks on the rear disc and rear axle hub.

  11. CONNECT REAR DISC BRAKE CALIPER ASSEMBLY


    1. A01GKRW

      Connect the rear disc brake caliper with 2 new bolts.

      Torque:
      86 N*m  { 877 kgf*cm, 63 ft.*lbf }

      Note


      • Do not twist the brake hose.

      • Make sure that the bolts are free from damage and foreign matter.

      • Do not overtighten the bolts.

  12. ADJUST PARKING BRAKE SHOE CLEARANCE


    1. Adjust parking brake shoe clearance Click here.

  13. INSTALL REAR WHEEL

    Torque:
    140 N*m  { 1428 kgf*cm, 103 ft.*lbf }

  14. PERFORM PARKING BRAKE SHOE BEDDING

    Click here