REAR STABILIZER BAR INSTALLATION

Tech Tips

A bolt without a torque specification is shown in the standard bolt chart Click here.


  1. INSTALL REAR STABILIZER BAR

    A01GJ6FE01

    1. Make sure the bracket's arrows face the front of the vehicle.

    2. A01GIISE02

      First temporarily install bolt 1. Then install bolts 2, 3 and 4. Then tighten bolt 5.

      Torque:
      51 N*m  { 520 kgf*cm, 38 ft.*lbf }

  2. INSTALL REAR STABILIZER LINK ASSEMBLY LH


    1. Install the stabilizer link with the 2 nuts and bolt.

      Torque:
      89 N*m  { 908 kgf*cm, 66 ft.*lbf, for stabilizer bar side }
      26 N*m  { 265 kgf*cm, 19 ft.*lbf, for No. 2 suspension arm side }

  3. INSTALL REAR STABILIZER LINK ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  4. INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY


    1. A01GHZJE01
      Text in Illustration
      *1 Attachment
      *2 Engine Lifter
      *a Attachment placement location

      Support the rear suspension member sub-assembly with an engine lifter using 4 attachments or equivalent tools.

      Note


      • Make sure to secure the rear suspension member sub-assembly to prevent it from dropping.

      • Use the attachments to keep the rear suspension member sub-assembly level.

      • The rear suspension member sub-assembly is a heavy component. Make sure that it is supported securely.

    2. Raise the rear suspension member sub-assembly until there is no clearance between the rear suspension member sub-assembly and the body.

      Note

      When raising the rear suspension member subassembly, be careful not to damage the vehicle body or other components installed on the vehicle.

    3. for Sports Package:

      A01GJ92E03
      Text in Illustration
      *A for Sports Package *B for Standard
      *1 Suspension Member Stopper Lower RH *2 Suspension Member Stopper Lower LH

      1. Install the 2 member stoppers with the 4 bolts labeled B, and install the 4 bolts labeled A.

        Torque:
        for bolt A
        19 N*m  { 194 kgf*cm, 14 ft.*lbf }
        for bolt B
        127 N*m  { 1295 kgf*cm, 94 ft.*lbf }

    4. for Standard:


      1. Install the 4 bolts labeled B.

        Torque:
        127 N*m  { 1295 kgf*cm, 94 ft.*lbf }

  5. CONNECT PNEUMATIC CYLINDER WITH REAR SHOCK ABSORBER ASSEMBLY LH (w/ Air Suspension)


    1. Connect the nut on the axle carrier.

      Torque:
      80 N*m  { 816 kgf*cm, 59 ft.*lbf }

  6. CONNECT PNEUMATIC CYLINDER WITH REAR SHOCK ABSORBER ASSEMBLY RH (w/ Air Suspension)

    Tech Tips

    Use the same procedures described for the LH side.

  7. CONNECT REAR SHOCK ABSORBER ASSEMBLY LH (w/o Air Suspension)


    1. Connect the nut on the axle carrier.

      Torque:
      80 N*m  { 816 kgf*cm, 59 ft.*lbf }

  8. CONNECT REAR SHOCK ABSORBER ASSEMBLY RH (w/o Air Suspension)

    Tech Tips

    Use the same procedures described for the LH side.

  9. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY LH


    1. A01GL1J

      Install the disc brake caliper with 2 new bolts.

      Torque:
      86 N*m  { 877 kgf*cm, 63 ft.*lbf }

  10. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  11. INSTALL PARKING BRAKE CABLE


    1. Install the cable with the 2 nuts to the vehicle side.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  12. INSTALL REAR SPEED SENSOR LH


    1. A01GLB8

      Install the sensor with the bolt.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note


      • The rear speed sensor is easily damaged. When installing the rear speed sensor to the rear axle hub RH, do not use excessive force to rotate and install it.

      • Prevent foreign matter from attaching to the sensor tip.

      • Do not drop the sensor. If the sensor has been dropped, replace the sensor with a new one.

  13. INSTALL REAR SPEED SENSOR RH

    Tech Tips

    Use the same procedures described for the LH side.

  14. INSTALL REAR WHEEL HOUSE LINER LH


    1. Install the liner with the 3 screws, 11 nuts, 2 clips to the vehicle side.

  15. INSTALL REAR WHEEL HOUSE LINER RH

  16. INSTALL NO. 5 ROCKER PANEL MOULDING PROTECTOR


    1. Install the protector for 1UR-FSE Click here.

    2. Install the protector for 1UR-FE Click here.

  17. INSTALL NO. 6 ROCKER PANEL MOULDING PROTECTOR


    1. Install the protector for 1UR-FSE Click here.

    2. Install the protector for 1UR-FE Click here.

  18. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

  19. CONNECT NO. 1 ACTUATOR HARNESS CLAMP


    1. Connect the 2 clamps and connector.

  20. INSTALL REAR WHEEL

    Torque:
    140 N*m  { 1428 kgf*cm, 104 ft.*lbf }

  21. CHECK SUSPENSION CONTROL SYSTEM (w/ Air Suspension)


    1. Check the suspension control system Click here.

  22. INSPECT AND ADJUST REAR WHEEL ALIGNMENT


    1. Inspect and adjust the rear wheel alignment Click here.

  23. CHECK SPEED SENSOR SIGNAL


    1. Check the speed sensor signal Click here.

  24. ADJUST HEADLIGHT ASSEMBLY

    Click here

  25. ADJUST OBJECT RECOGNITION CAMERA

    Click here