FRONT DRIVE SHAFT ASSEMBLY DISASSEMBLY

Note


  • When using a vise, place aluminum plates between the part and vise.

  • When using a vise, do not overtighten it.


  1. REMOVE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP LH


    1. A01GLJPE11
      Text in Illustration
      *a for One Touch Type
      *b for Claw Engagement Type

      for One Touch Type:

      Using a screwdriver, remove the front No. 2 axle inboard joint boot clamp LH as shown in the illustration.

    2. for Claw Engagement Type:

      Using needle-nose pliers, remove the front No. 2 axle inboard joint boot clamp LH as shown in the illustration.

  2. REMOVE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP RH

    Tech Tips

    Use the same procedure described for the LH side.

  3. REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP LH

    Tech Tips

    Use the same procedure described for the front No. 2 axle inboard joint boot clamp LH.

  4. REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP RH

    Tech Tips

    Use the same procedure described for the LH side.

  5. DISCONNECT INBOARD JOINT BOOT


    1. Disconnect the inboard joint boot from the front drive inboard joint assembly.

  6. REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY LH


    1. Remove any old grease from the front drive inboard joint assembly LH.

    2. A01GKX0E02
      Text in Illustration
      *a Matchmark

      Put matchmarks on the front drive inboard joint assembly LH and front drive outboard joint shaft assembly LH.

      Note

      Do not use a punch to make the matchmarks.

    3. Remove the front drive inboard joint assembly LH from the front drive outboard joint shaft assembly LH.

    4. A01GM8Y

      Using a snap ring expander, remove the front drive inner shaft inner shaft snap ring LH.

    5. A01GJ2HE02
      Text in Illustration
      *a Matchmark

      Put matchmarks on the front drive outboard joint shaft assembly LH and tripod joint.

      Note

      Do not use a punch to make the matchmarks.

    6. Using a brass bar and hammer, remove the tripod joint from the front drive outboard joint shaft assembly LH.

      Note

      Do not tap the roller.

  7. REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  8. REMOVE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP LH


    1. A01GI7H

      Using pliers, remove the front No. 2 axle outboard joint boot clamp LH as shown in the illustration.

  9. REMOVE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP RH

    Tech Tips

    Use the same procedure described for the LH side.

  10. REMOVE FRONT AXLE OUTBOARD JOINT BOOT CLAMP LH


    1. A01GJ20

      Using pliers, remove the front axle outboard joint boot clamp LH as shown in the illustration.

  11. REMOVE FRONT AXLE OUTBOARD JOINT BOOT CLAMP RH

    Tech Tips

    Use the same procedure described for the LH side.

  12. REMOVE OUTBOARD JOINT BOOT


    1. Remove the outboard joint boot from the front drive outboard joint shaft assembly.

    2. Remove any old grease from the front drive outboard joint shaft assembly.

  13. REMOVE FRONT DRIVE SHAFT DUST COVER LH


    1. A01GMMLE05

      Using SST and a press, remove the front drive shaft dust cover LH.

      SST
      09950-00020

      Note

      Be careful not to drop the front drive inboard joint assembly.

  14. REMOVE FRONT DRIVE SHAFT BEARING


    1. A01GMPS

      Using a snap ring expander, remove the front drive shaft hole snap ring RH.

    2. A01GJZWE01

      Using SST and a press, remove the front drive shaft bearing.

      SST
      09527-10011

      Note

      Be careful not to drop the front drive inboard joint assembly.