VALVE BODY ASSEMBLY INSTALLATION


  1. INSTALL TRANSMISSION VALVE BODY ASSEMBLY

    A01GM97

    1. Install the spring and check ball body.

    2. A01GLM8E01

      Align the groove of the manual valve with the lever pin.

    3. A01GKDHE01

      Install the 17 bolts.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

      Tech Tips

      Each bolt length is indicated below.

      Bolt length
      21 mm (0.83 in.) for bolt A
      31 mm (1.22 in.) for bolt B
      64 mm (2.52 in.) for bolt C
    4. A01GHP8

      Install the detent spring and detent spring cover with the bolt.

      Note

      Make sure to install the detent spring so that its roller is perpendicularly at the center of the manual valve lever.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }
    5. A01GLSS

      Connect the 8 connectors to the solenoid valves.

    6. Connect the oil pressure switch connector.

    7. Coat a new O-ring with ATF and install to the ATF temperature sensor.

    8. Install the ATF temperature sensor and lock plate with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  2. INSTALL VALVE BODY OIL STRAINER ASSEMBLY

    A01GLWTE01

    1. Coat a new O-ring with ATF and install it to the oil strainer.

      Note

      Ensure that the O-ring is not twisted or pinched.

    2. A01GKXI

      Install the oil strainer to the valve body with the 4 bolts.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

  3. INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

    A01GLOIE01

    1. Install the 3 magnets to the oil pan.

    2. A01GN2W

      Install a new gasket and the oil pan to the transmission case with the 9 bolts.

      Torque:
      7.3 N*m  { 74 kgf*cm, 64 in.*lbf }

      Note


      • A01GMX5E01

      • Make sure that there is no oil or foreign matter on the gasket seal surface and oil pan contact surface.

      • Install the gasket so that there is no slack in the gasket, and that the seal surface's entire circumference is level.

      • Make sure that the 9 gasket drop prevention protrusions are set on the oil pan.

      • When tightening the oil pan, make sure that the gasket is not pinched between the gasket tightening area's sleeve and the transmission's seal surface.

  4. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  5. INSTALL COWL TOP VENTILATOR LOUVER


    1. A01GM4S

      for LHD:

      Install the 6 clips and cowl top ventilator louver RH.

      Note

      If the cowl top ventilator louver RH is not properly installed, water may leak into the engine room and cause malfunctions. Therefore, make sure the cowl top ventilator louver RH is installed properly.

    2. A01GI9P

      for RHD:

      Install the 6 clips and cowl top ventilator louver LH.

      Note

      If the cowl top ventilator louver LH is not properly installed, water may leak into the engine room and cause malfunctions. Therefore, make sure the cowl top ventilator louver LH is installed properly.

  6. ADD AUTOMATIC TRANSMISSION FLUID


    1. Add automatic transmission fluid Click here.

  7. CHECK AUTOMATIC TRANSMISSION SYSTEM PRECAUTION


    1. After replacing the valve body or solenoid valve, certain procedures are necessary Click here.