AUTOMATIC TRANSMISSION SYSTEM, Diagnostic DTC:P0771

DTC Code DTC Name
P0771 Shift Solenoid "E" Performance (Shift Solenoid Valve SR)

DESCRIPTION

Tech Tips

Gear shift position when a problem occurs in shift solenoid valve SR:

TCM gear shift command 1st 2nd 3rd 4th 5th 6th 7th 8th
Actual gear position under SR stuck OFF malfunction 1 7th 7th 7th 7th 7th 7th 7th 7th
Actual gear position under SR stuck OFF malfunction 2 3rd 3rd 3rd 3rd 7th 7th 7th 7th
DTC Code

DTC Detection Condition


  1. Diagnosis Condition

  2. Malfunction Status

  3. Malfunction Time

  4. Other

Trouble Area
P0771
  1. ECT is 40°C (104°F) or higher, ATF temperature is -10°C (14°F) or higher, and the vehicle is driven with the shift lever in D (no malfunctions are detected in shift solenoid valve SL1, 2, 3, 4 and 5, SR, speed sensors (NT, NC3, SP2), engine coolant temperature sensor, oil temperature sensor, knock control sensor, electronic throttle, or CAN2)

  2. When gear shifts to 5th to 8th are requested by the TCM, the engine overruns (neutral status)

  3. Malfunction status continues for 0.5 sec. or more (1 trip)

  4. 2 trip detection logic


  • Shift solenoid valve SL2

  • Shift solenoid valve SR

  • Valve body assembly

  • Torque converter clutch assembly

  • Automatic transmission assembly

P0771
  1. ECT is 40°C (104°F) or higher, ATF temperature is -10°C (14°F) or higher, and the vehicle is driven with the shift lever in D (no malfunctions are detected in shift solenoid valve SL1, 2, 3, 4 and 5, SR, speed sensors (NT, NC3, SP2), engine coolant temperature sensor, oil temperature sensor, knock control sensor, electronic throttle, or CAN2)

  2. One of the following occurs:


    1. When gear shifts to 1st are requested by the TCM, the actual gear changes to 3rd gear

    2. When gear shifts to 2nd are requested by the TCM, the actual gear changes to 3rd gear

    3. When gear shifts to 4th are requested by the TCM, the actual gear changes to 3rd gear

    4. When gear shifts to 5th are requested by the TCM, the actual gear changes to 7th gear

    5. When gear shifts to 6th are requested by the TCM, the actual gear changes to 7th gear

    6. When gear shifts to 8th are requested by the TCM, the actual gear changes to 7th gear

  3. Malfunction status occurs 2 times per trip

  4. 2 trip detection logic


  • Shift solenoid valve SL3

  • Shift solenoid valve SR

  • Valve body assembly

  • Torque converter clutch assembly

  • Automatic transmission assembly

MONITOR DESCRIPTION

This DTC indicates a stuck ON malfunction or stuck OFF malfunction of shift solenoid valve SR.

The TCM commands gear shifts by turning the shift solenoid valves on/off. When the gear position commanded by the TCM and the actual gear position are not the same, the TCM illuminates the MIL and stores the DTC.

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK DTC OUTPUT (IN ADDITION TO DTC P0771, P0776, P0796 AND P2714)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Powertrain / ECT / DTC.

    5. Read the DTCs using the intelligent tester.

      Result
      Display (DTC output) Proceed to
      Only P0771, P0776 and P2714 are output A
      Only P0771, P0796 and P2714 are output B
      P0771, P0796, P2714, and other DTCs are output C

      Tech Tips

      If any other codes besides P0771, P0776, P0796 and P2714 are output, perform troubleshooting for those DTCs first.


    B
    C
    A