IGNITION COIL AND SPARK PLUG INSTALLATION


  1. INSTALL SPARK PLUG


    1. Using a 16 mm plug wrench, install the 8 spark plugs.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  2. INSTALL IGNITION COIL ASSEMBLY


    1. A01GKK9E01

      Perform a visual inspection on the spark plug tube gasket.

      Standard
      Inspection Area Inspection Result
      Upper surface No scratches or deformation
      Outer lip No scratches or deformation
      Inner lip No scratches
    2. A01GL7W

      Set each spark plug tube gasket on each ignition coil assembly.

    3. A01GNL6

      After installing each spark plug tube gasket, securely insert each ignition coil assembly.

    4. Install the 8 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    5. Connect the 8 ignition coil ignition coil assembly connectors.

  3. INSTALL AIR CLEANER ASSEMBLY RH

    A01GM6U

    1. Install the air cleaner case RH with the 2 nuts and clip.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

    2. Install the air cleaner element to the air cleaner case RH.

    3. A01GIMA

      Install the air cleaner cap RH with the 2 clamps.

    4. Connect the mass air flow meter connector.

  4. INSTALL AIR CLEANER ASSEMBLY LH

    A01GJKZ

    1. Install the air cleaner case LH with the 2 nuts and clip.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

    2. Install the air cleaner element to the air cleaner case LH.

    3. A01GJIY

      Install the air cleaner cap LH with the 2 clamps.

    4. Connect the mass air flow meter connector.

  5. INSTALL SKID CONTROL ECU BRACKET

    Click here

  6. INSTALL BATTERY TRAY


    1. Install the battery tray with the 3 bolts.

      Torque:
      5.4 N*m  { 55 kgf*cm, 47 in.*lbf }

  7. INSTALL BATTERY


    1. Install the battery.

    2. Install the battery insulator.

    3. Install the No. 2 battery clamp bolt and battery clamp with the nut.

      Torque:
      2.9 N*m  { 30 kgf*cm, 26 in.*lbf }

    4. Connect the battery cable clamp.

    5. Connect the positive (+) battery cable to the battery terminal.

      Torque:
      5.6 N*m  { 57 kgf*cm, 50 in.*lbf }

  8. INSTALL INTAKE AIR CONNECTOR PIPE


    1. Align the protrusion of the intake air resonator with the cutout of the bracket and insert the protrusion.

    2. Install the intake air connector pipe with the 3 hose clamps.

      Torque:
      for intake air connector pipe and throttle body
      4.8 N*m  { 49 kgf*cm, 42 in.*lbf }
      for intake air connector pipe and air cleaner cap
      3.8 N*m  { 39 kgf*cm, 34 in.*lbf }

      Tech Tips


      • Insert the protrusion of the intake air connector pipe into the hole of the hose clamp.

      • The intake air connector pipe and throttle body clamp can be tightened within the range of 4.0 N*m (41 kgf*cm, 35 in.*lbf) to 5.5 N*m (56 kgf*cm, 49 in.*lbf), and the intake air connector pipe and air cleaner cap clamp can be tightened within the range of 2.0 N*m (20 kgf*cm, 18 in.*lbf) to 5.5 N*m (56 kgf*cm, 49 in.*lbf).

    3. Attach the 2 wire harness clamps.

    4. A01GMMEE03

      Connect the No. 1 and No. 2 ventilation hoses to the intake air connector pipe.

      Tech Tips


      • Position the claws of the clamps as shown in the illustration.

      • Install the clamps so that they are within the hose's paint marks.

  9. INSTALL NO. 1 AIR CLEANER INLET

    A01GME8E01

    1. Align the holes with the connection areas labeled A, and attach the No. 1 air cleaner inlet.

    2. A01GM3N

      Install the No. 1 air cleaner inlet with the 2 bolts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  10. INSTALL ENGINE ROOM SIDE COVER RH


    1. Install the engine room side cover RH with the 5 clips.

  11. INSTALL ENGINE ROOM SIDE COVER LH


    1. Install the engine room side cover LH with the 5 clips.

  12. INSTALL AIR CLEANER INLET COVER SUB-ASSEMBLY

    A01GNHGE01

    1. Attach the 4 clips B.

      Note


      • Make sure the clips are attached securely.

      • Attaching the clips forcefully or hitting the top of the clips may damage them.

    2. Install the air cleaner inlet cover sub-assembly with the 5 clips labeled A.

  13. INSTALL V-BANK COVER SUB-ASSEMBLY

    A01GLQ5E01

    1. After sliding the cover from the vehicle front to the rear to attaching the 2 clips labeled A, attach the 4 clips labeled B and install the V-bank cover sub-assembly.

      Note


      • Make sure the clips are attached securely.

      • Attaching the clips forcefully or hitting the top of the clips may damage them.

  14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  15. INSTALL COWL TOP VENTILATOR LOUVER RH


    1. A01GM4S

      Install the 6 clips and cowl top ventilator louver RH.

      Note

      If the cowl top ventilator louver RH is not properly installed, water may leak into the engine room and cause malfunctions. Therefore, make sure the cowl top ventilator louver RH is installed properly.