OIL PUMP (for AWD) REMOVAL


  1. REMOVE ENGINE AND TRANSMISSION

    Click here

  2. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    1. A01GM9G

      Remove the standard bolt, 6 mm hexagon wrench bolt and belt tensioner.

  3. REMOVE FRONT WATER BY-PASS JOINT


    1. A01GHO4

      Remove the 4 nuts, water by-pass joint and 2 gaskets.

  4. REMOVE CAMSHAFT TIMING CONTROL WITH EDU MOTOR ASSEMBLY LH


    1. A01GIVB

      Disconnect the 2 camshaft timing control with EDU motor assembly LH connectors and engine wire clamp.

    2. A01GHPG

      Remove the 3 bolts and camshaft timing control with EDU motor assembly LH.

      Note

      Do not allow foreign matter to contact the oil seal face of the camshaft timing control with EDU motor assembly LH (connecting surface with timing chain cover).

    3. Remove the O-ring from the timing chain cover.

  5. REMOVE CAMSHAFT TIMING CONTROL WITH EDU MOTOR ASSEMBLY RH


    1. A01GML7

      Disconnect the 2 camshaft timing control with EDU motor assembly RH connectors.

    2. Remove the bolt and engine wire bracket.

    3. A01GIJS

      Remove the 3 bolts and camshaft timing control with EDU motor assembly RH.

      Note

      Do not allow foreign matter to contact the oil seal face of the camshaft timing control with EDU motor assembly RH (connecting surface with timing chain cover).

    4. Remove the O-ring from the timing chain cover.

  6. REMOVE OIL FILTER ELEMENT


    1. A01GJULE11
      Text in Illustration
      *1 Pipe
      *2 Hose

      Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.

    2. A01GNHB

      Remove the oil filter drain plug.

      Tech Tips

      Use a container to catch the draining oil.

    3. A01GM81E02
      Text in Illustration
      *1 Oil Filter Cap
      *2 Valve
      *3 Pipe
      *4 O-Ring
      *5 Hose

      Install the pipe to the oil filter cap.

      Note

      If the O-ring is removed with the drain plug, install the O-ring together with the pipe.

    4. A01GMFO

      Check that oil is drained from the oil filter. Then disconnect the pipe and remove the O-ring as shown in the illustration.

    5. A01GMPVE02
      Text in Illustration
      *1 Oil Filter Bracket Clip

      Using SST, remove the oil filter cap.

      SST
      09228-06501

      Note

      Do not remove the oil filter bracket clip.

    6. A01GMCZE03
      Text in Illustration
      *1 O-Ring

      Remove the oil filter element and O-ring from the oil filter cap.

      Note

      Be sure to remove the O-ring (for the cap) by hand, without using any tools, to prevent damage to the groove.

  7. REMOVE OIL FILTER BRACKET


    1. A01GL3X

      Remove the 3 bolts, filter bracket and 2 gaskets.

  8. REMOVE CRANKSHAFT PULLEY


    1. A01GMVCE01

      Using SST, loosen the crankshaft pulley set bolt.

      SST
      09213-54015   ( 90119-08216 )
      09330-00021
    2. A01GN76E01

      Using the pulley set bolt and SST, remove the crankshaft pulley.

      SST
      09950-50013   ( 09951-05010, 09952-05010, 09953-05010, 09954-05011 )
  9. REMOVE IGNITION COIL ASSEMBLY


    1. A01GKPD

      Disconnect the 8 ignition coil assembly connectors.

    2. Remove the 8 bolts.

    3. A01GNKFE02

      Using a screwdriver, pry up each spark plug tube gasket at the cutouts to remove the 8 ignition coil assemblies together with the 8 spark plug tube gaskets.

      Note

      Do not damage the cylinder head cover when removing the spark plug tube gasket.

      Tech Tips

      Tape the screwdriver tip before use.

  10. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH


    1. A01GKDQ

      Remove the 15 bolts, 2 seal washers, cylinder head cover and gasket.

      Tech Tips

      Make sure the removed parts are returned to the same places they were removed from.

    2. A01GILM

      Remove the 4 gaskets and 2 O-rings from the camshaft bearing caps (No. 2, No. 3, No. 7).

  11. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH


    1. A01GHZK

      Remove the 15 bolts, 2 seal washers, cylinder head cover and gasket.

      Tech Tips

      Make sure the removed parts are returned to the same places they were removed from.

    2. A01GM0S

      Remove the 4 gaskets and 2 O-rings from the camshaft bearing caps (No. 1, No. 3, No. 6).

  12. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY


    1. A01GL8Q

      Remove the 2 plugs and 2 gaskets.

    2. A01GNFEE01

      Remove the 30 bolts and nut shown in the illustration.

    3. A01GK19

      Remove the timing chain cover by prying between the timing chain cover and cylinder head and cylinder block with a screwdriver as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

      Note

      Be careful not to damage the contact surfaces of the cylinder head, cylinder block and chain cover.

    4. A01GII0

      Remove the oil pump gasket from the cylinder block.

    5. A01GNMX

      Remove the O-ring from the cylinder block.

  13. REMOVE WATER INLET PIPE


    1. A01GIAM

      Remove the water inlet pipe.

    2. Remove the 2 O-rings from the water inlet pipe.

  14. REMOVE CRANKSHAFT TIMING GEAR KEY


    1. A01GL39

      Using a screwdriver, remove the 2 timing gear keys from the crankshaft.

  15. REMOVE TIMING CHAIN CASE OIL SEAL


    1. A01GNDT

      Remove the timing chain case oil seal with a screwdriver.

      Tech Tips

      Tape the screwdriver tip before use.

      Note

      Do not damage the surface of the timing chain case oil seal press fit hole and crankshaft.