ENTRY AND START SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are for reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the tester on.

    4. Enter the following menus:

      Select: Body / (desired system) / Data List /

    5. According to the display on tester, read the "Data List".

      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      IG SW Engine switch on (IG)/ON or OFF

      ON: Engine switch is on (IG)

      OFF: Engine switch is off

      		 -
      ACC SW Engine switch on (ACC)/ON or OFF

      ON: Engine switch is on (ACC)

      OFF: Engine switch is off

      		 -
      Start Switch1 Start switch 1/ON or OFF

      ON: Engine switch is on (IG)

      OFF: Engine switch is off

      		 -
      Start Switch2 Start switch 2/ON or OFF

      ON: Engine switch is on (IG)

      OFF: Engine switch is off

      		 -
      Steering Unlock Switch Steering lock condition/ON or OFF

      ON: Steering is unlocked

      OFF: Steering is locked

      		 -
      Neutral SW/ Clutch SW Park / neutral position switch/ON or OFF

      ON: Shift lever in P or N

      OFF: Shift lever in R or D

      		 -
      Vehicle Speed Signal Vehicle speed signal/STOP or RUN

      STOP: Vehicle is stopped

      RUN: Vehicle is running

      		 -
      Engine Condition Engine condition/STOP or RUN

      STOP: Engine is stopped

      RUN: Engine is running

      		 -
      IG1 Relay Monitor(Outside) D-IG1-1 relay outer relay monitor/ON or OFF

      ON: Engine switch is on (IG)

      OFF: Engine switch is off

      		 -
      IG2 Relay Monitor(Outside) IG2 outer relay monitor/ON or OFF

      ON: Engine switch is on (IG)

      OFF: Engine switch is off

      		 -
      IG1 Relay Monitor(Inside) D-IG1-1 relay inner relay monitor/ON or OFF

      ON: Engine switch is on (IG)

      OFF: Engine switch is off

      		 -
      IG2 Relay Monitor(Inside) IG2 inner relay monitor/ON or OFF

      ON: Engine switch is on (IG)

      OFF: Engine switch is off

      		 -
      ACC Relay Monitor D-ACC relay monitor/ON or OFF

      ON: Engine switch is on (ACC)

      OFF: Engine switch is off

      		 -
      Latch Circuit Ratch circuit/ON or OFF

      ON: Engine switch is on (IG)

      OFF: Engine switch is off, on (ACC) or engine is running

      		 -
      Starter Request Signal Starter request signal/ON or OFF

      ON: ST/IGCT relay is ON

      OFF: ST/IGCT relay is OFF

      		 -
      Power Supply Condition Power supply condition/ALL, ACC ON, IG1 IG2, ST ON

      ALL: All relays are ON

      ACC ON: D-ACC relay is ON

      IG1: D-IG1-1 relay is ON

      IG2: IG2 relay is ON

      ST ON: ST/IGCT relay is ON

      		 -
      Starter Relay Monitor Starter relay monitor/ON or OFF

      ON: Starter relay is ON

      OFF: Starter relay is OFF

      		 -
      #Codes Number of diagnosis codes/Min: 0, Max: 255 - -
      Stop Light SW Stop light switch/ON or OFF

      ON: Brake pedal is depressed

      OFF: Brake pedal is released

      		 -
      Entry & Start
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Ignition Switch Engine switch/ON or OFF

      ON: Engine switch is on (IG)

      OFF: Engine switch is off

      		 -
      Key Low Battery Key battery conditions/ON or OFF

      ON: Battery is depleted

      OFF: Battery is not depleted

      		 -
      Unmatch Code or Form Code format/YES or NO

      YES: Code format matches

      NO: Code format differs

      		 -
      No Response Response/YES or NO

      YES: Response

      NO: No response

      		 -
      ID Code Difference(Resp) ID code/YES or NO

      YES: ID code matches

      NO: ID code differs

      		 -
      C Code Difference Challenge code/YES or NO

      YES: Challenge code matches

      NO: Challenge code differs

      		 -
      Unmatched Vehicle-ID Key number/YES or NO

      YES: Key number matches

      NO: Key number differs

      		 -
      S Code Check S code certification result/NG or OK

      NG: S code certification result is abnormal

      OK: S code certification result is normal

      		 -
      L Code Check L code certification result/NG or OK

      NG: L code certification result is abnormal

      OK: L code certification result is normal

      		 -
      Ignition Available Area Key area where engine start is possible/All or Front

      All: All areas

      Front: Front only

      		 -
      Body No.4
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Stop Light Tr. Stop light switch/ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      		 -

  2. PERFORM ACTIVE TEST

    Tech Tips

    Using the intelligent tester to perform the Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the tester ON.

    4. Enter the following menus:

      Select: Body / (desired system) / Active Test /

    5. According to the display on tester, perform the "Active Test".

    Main Body
    Tester Display Test Part Control Range Diagnostic Note
    Indicator for Lighting Indicator illumination ON/OFF -
    Indicator Condition Indicator light illumination pattern Green/Amber/No Sig -
    P Supply for Steering Lock Steering lock ECU power supply ON/OFF -
    Entry & Start
    Tester Display Test Part Control Range Diagnostic Note
    Fr-Seat Inside Transmitter Indoor key antenna (for front) ON / OFF -
    Rr-Seat Inside Transmitter Indoor key antenna (for rear1) ON / OFF -
    Inside Trunk/Backdoor Transmitter Indoor key antenna (for rear2) ON / OFF -