OIL PUMP INSTALLATION

INSTALL WATER INLET PIPE
1. Apply soapy water to 2 new O-rings and install them to the inlet pipe.
2. Install the inlet pipe to the No. 1 heat exchanger cover.

INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

Install a new oil pump gasket.
Install a new O-ring.

Apply seal packing in a continuous line to the timing chain cover as shown in the following illustration.

Seal packing
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

Apply Seal Packing as Follows

Area	Seal packing diameter	Application position from inside edge of cover
Continuous Line Area	3.0 to 4.0 mm (0.1181 to 0.1575 in.)	2.5 mm (0.098 in.)
Dashed Line Area	6.4 mm (0.2520 in.) or more, or within OK area shown in illustration	0.5 mm (0.020 in.)
Diagonal Line Area	3.0 to 4.0 mm (0.1181 to 0.1575 in.)	5.5 mm (0.217 in.)

Note

When the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.
Install the chain cover within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.
Do not start the engine for at least 2 hours after installation.

Align the drive rotor spline of the oil pump and the crankshaft as shown in the illustration. Install the spline and chain cover to the crankshaft.

Temporarily tighten the timing chain cover with the 30 bolts and nut.

Bolt Length

Item	Length	Thread diameter
Bolt A	25 mm (0.984 in.)	8 mm (0.315 in.)
Bolt B	55 mm (2.165 in.)	8 mm (0.315 in.)
Bolt C	70 mm (2.756 in.)	8 mm (0.315 in.)
Bolt D	35 mm (1.378 in.)	10 mm (0.394 in.)
Bolt E	55 mm (2.165 in.)	10 mm (0.394 in.)
Bolt F	80 mm (3.150 in.)	10 mm (0.394 in.)

Note

Make sure that there is no oil on the bolt threads.

Tighten the 11 bolts in several steps, in the sequence shown in the illustration.

Torque:

47 N*m { 479 kgf*cm, 35 ft.*lbf }
Temporarily tighten the belt tensioner with the standard bolt and 6 mm hexagon wrench bolt.
Tighten the 21 bolts and nut in several steps, in the sequence shown in the illustration.

Torque:

23 N*m { 235 kgf*cm, 17 ft.*lbf }

Note

After the installation, if the seal packing has seeped out at the areas labeled A shown in the illustration, wipe it off.
Install the 2 new gaskets and the 2 plugs.

Torque:

46 N*m { 469 kgf*cm, 34 ft.*lbf }

INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 1)
1. Install 4 new gaskets and 2 new O-rings to the camshaft bearing caps (No. 2, No. 3, No. 7).
2. Install a new gasket to the cylinder head cover.
  
  Note
  
  Remove any oil from the contact surface.
3. Apply seal packing as shown in the illustration.
  
  Seal packing
  
  Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
  Note
  
  Remove any oil from the contact surface.
  
  Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
  
  Do not start the engine for at least 2 hours after the installation.
4. Install the cylinder head cover with 2 new seal washers and the 15 bolts.
  
  Torque:
  
  for bolt A
  
  21 N*m { 214 kgf*cm, 15 ft.*lbf }
  
  except bolt A
  
  12 N*m { 122 kgf*cm, 9 ft.*lbf }
INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 2)
1. Install 4 new gaskets and 2 new O-rings to the camshaft bearing caps (No. 1, No. 3, No. 6).
2. Install a new gasket to the cylinder head cover.
  
  Note
  
  Remove any oil from the contact surface.
3. Apply seal packing as shown in the illustration.
  
  Seal packing
  
  Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
  Note
  
  Remove any oil from the contact surface.
  
  Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
  
  Do not start the engine for at least 2 hours after the installation.
4. Install the cylinder head cover with 2 new seal washers and the 15 bolts.
  
  Torque:
  
  for bolt A
  
  21 N*m { 214 kgf*cm, 15 ft.*lbf }
  
  except bolt A
  
  12 N*m { 122 kgf*cm, 9 ft.*lbf }

INSTALL IGNITION COIL ASSEMBLY

Perform a visual inspection on the spark plug tube gasket.

Standard

Inspection Area	Inspection Result
Upper surface	No scratches or deformation
Outer lip	No scratches or deformation
Inner lip	No scratches

Set each spark plug tube gasket on each ignition coil assembly.
After installing each spark plug tube gasket, securely insert each ignition coil assembly.
Install the 8 bolts.

Torque:

10 N*m { 102 kgf*cm, 7 ft.*lbf }
Connect the 8 ignition coil ignition coil assembly connectors.

INSTALL CRANKSHAFT PULLEY
1. Align the pulley set key with the key groove of the pulley, and slide on the pulley.
2. Using SST, install the pulley bolt.
  
  SST
  
  09213-54015 ( 90119-08216 )
  
  09330-00021
  
  Torque:
  
  300 N*m { 3059 kgf*cm, 221 ft.*lbf }
INSTALL RESONATOR BRACKET SUB-ASSEMBLY
1. Install the resonator bracket sub-assembly with the bolt.
  
  Torque:
  
  20 N*m { 204 kgf*cm, 15 ft.*lbf }
INSTALL OIL FILTER BRACKET
1. Install 2 new gaskets and the filter bracket with the 3 bolts.
  
  Torque:
  
  21 N*m { 214 kgf*cm, 15 ft.*lbf }

INSTALL OIL FILTER ELEMENT

Clean the inside of the oil filter cap, the threads and O-ring groove.

Text in Illustration
*1	O-Ring
*a	CORRECT
*b	INCORRECT

Apply a small amount of engine oil to a new O-ring for the cap, and then install the O-ring to the groove of the oil filter cap.

Note

Be sure to install the O-ring in the proper location, otherwise oil may leak.
Do not twist the O-ring.

Set a new oil filter element to the oil filter cap.
Remove any dirt or foreign matter from the installation surface of the engine.
Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.

Note

Do not pinch the O-ring for the cap.

Text in Illustration
*1	Oil Filter Bracket
*2	Oil Filter Cap
*3	O-Ring
*4	Oil Filter Bracket
*a	No Clearance

Using SST, tighten the oil filter cap.

SST: 09228-06501

Torque:: 25 N*m { 255 kgf*cm, 18 ft.*lbf }

Note

When tightening the oil filter cap, do not remove the oil filter bracket clip.
Make sure that the oil filter is installed securely as shown in the illustration.
Be careful that the O-ring does not get caught between the parts.

Text in Illustration

*1 O-Ring

Apply a small amount of engine oil to a new drain plug O-ring, and install it to the oil filter cap.

Note

Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.
Install the oil filter drain plug.

Torque:

13 N*m { 133 kgf*cm, 10 ft.*lbf }

Note

Be careful that the O-ring does not get caught between the parts.

INSTALL CAMSHAFT TIMING CONTROL MOTOR ASSEMBLY LH (for Bank 1)
1. Turn the camshaft timing gear assembly's eccentric shaft index slot in the counterclockwise direction by hand, and set it to the maximum retard angle position.
  Tech Tips
  
  When the cam of the camshaft lifts the valve, the eccentric shaft becomes difficult to turn.
  
  The position where the eccentric shaft stops is the maximum retard angle.
2. Install a new O-ring to the timing chain cover.
3. Align the joint of the camshaft timing control motor LH and the keyway of the camshaft timing gear assembly, and install the motor with the 3 bolts.
  
  Torque:
  
  21 N*m { 214 kgf*cm, 15 ft.*lbf }
  Note
  
  Check that [L] is printed on the label of the camshaft timing control motor LH.
  
  Do not allow foreign matter to contact the oil seal face of the camshaft timing control motor LH (connecting surface with timing chain cover sub-assembly).
  
  When installing the camshaft timing control motor LH, do not use excessive force.
  
  Align the timing chain cover sub-assembly knock pin with the camshaft timing control motor LH pin hole to install the camshaft timing control motor LH.
  
  Install the camshaft timing control motor LH with the arrow facing upward, as shown in the illustration.
  
  Do not drop the camshaft timing control motor LH. If dropped, replace it.
  
  Do not disassemble the camshaft timing control motor LH. If disassembled, replace it.
4. Connect the 2 camshaft timing control motor LH connectors and engine wire clamp.
INSTALL CAMSHAFT TIMING CONTROL MOTOR ASSEMBLY (for Bank 2)
1. Turn the camshaft timing gear assembly's eccentric shaft index slot in the counterclockwise direction by hand, and set it to the maximum retard angle position.
  Tech Tips
  
  When the cam of the camshaft lifts the valve, the eccentric shaft becomes difficult to turn.
  
  The position where the eccentric shaft stops is the maximum retard angle.
2. Install a new O-ring to the timing chain cover.
3. Align the joint of the camshaft timing control motor RH and the keyway of the camshaft timing gear assembly, and install the motor with the 3 bolts.
  
  Torque:
  
  21 N*m { 214 kgf*cm, 15 ft.*lbf }
  Note
  
  Check that [R] is printed on the label of the camshaft timing control motor RH.
  
  Do not allow foreign matter to contact the oil seal face of the camshaft timing control motor RH (connecting surface with timing chain cover sub-assembly).
  
  When installing the camshaft timing control motor RH, do not use excessive force.
  
  Align the timing chain cover sub-assembly knock pin with the camshaft timing control motor RH pin hole to install the camshaft timing control motor RH.
  
  Install the camshaft timing control motor RH with the arrow facing upward, as shown in the illustration.
  
  Do not drop the camshaft timing control motor RH. If dropped, replace it.
  
  Do not disassemble the camshaft timing control motor RH. If disassembled, replace it.
4. Install the engine wire bracket with the bolt.
  
  Torque:
  
  10 N*m { 102 kgf*cm, 7 ft.*lbf }
5. Connect the 2 camshaft timing control motor RH connectors.
INSTALL FRONT WATER BY-PASS JOINT
1. Install the water by-pass joint and 2 new gaskets with the 4 nuts.
  
  Torque:
  
  21 N*m { 214 kgf*cm, 15 ft.*lbf }
INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY
1. Install the bolt and No. 1 idler pulley sub-assembly.
  
  Torque:
  
  43 N*m { 438 kgf*cm, 32 ft.*lbf }
  
  Tech Tips
  
  Install the No. 1 idler pulley sub-assembly in the direction shown in the illustration.
INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY
1. Install the bolt and No. 2 idler pulley sub-assembly.
  
  Torque:
  
  43 N*m { 438 kgf*cm, 32 ft.*lbf }
INSTALL WATER PUMP PULLEY
1. Temporarily install the pulley with the 4 bolts.
2. Using SST, hold the pulley and tighten the 4 bolts.
  
  SST
  
  09960-10010 ( 09962-01000, 09963-01000 )
  
  Torque:
  
  21 N*m { 214 kgf*cm, 15 ft.*lbf }
INSTALL WATER INLET HOUSING
1. Install the inlet housing and new gasket with the 3 bolts.
  
  Torque:
  
  21 N*m { 214 kgf*cm, 15 ft.*lbf }
2. Using needle-nose pliers, grip the claws of the clips and slide the clips to connect the water by-pass hoses and water inlet hose.
INSTALL NO. 2 ENGINE COVER SUB-ASSEMBLY LH
INSTALL NO. 3 ENGINE COVER
INSTALL INTAKE MANIFOLD
1. Install 2 new gaskets to the intake manifold.
2. Temporarily install the intake manifold with the 2 nuts and 8 bolts. Then tighten the 2 nuts and 8 bolts uniformly in the order shown in the illustration.
  
  Torque:
  
  21 N*m { 214 kgf*cm, 15 ft.*lbf }
3. Connect the No.1 ventilation hose to the intake manifold.
  
  Note
  
  Face the claws of the clips as shown in the illustration.
INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY
1. Install the water by-pass pipe sub-assembly to the intake manifold with the 2 bolts.
2. Connect the heater water inlet hose, heater water outlet hose, water inlet hose, and No. 3 water by-pass hose to the water by-pass pipe sub-assembly with the 4 clamps.
  
  Note
  
  Face the No. 3 water by-pass hose clip as shown in the illustration.
INSTALL GENERATOR ASSEMBLY
1. Using an E8 "TORX" socket wrench, set the generator with the 2 stud bolts.
  
  Torque:
  
  10 N*m { 102 kgf*cm, 7 ft.*lbf }
2. Install the generator with the 2 bolts and 2 nuts.
  
  Torque:
  
  43 N*m { 438 kgf*cm, 32 ft.*lbf }
3. Connect the generator connector.
4. Connect the harness to the +B terminal with the nut.
  
  Torque:
  
  12 N*m { 122 kgf*cm, 9 ft.*lbf }
INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
1. Apply a light coat of engine oil to a new O-ring.
2. Install the new O-ring to the engine oil level dipstick guide.
3. Install the engine oil level dipstick guide with the 2 bolts.
  
  Torque:
  
  10 N*m { 102 kgf*cm, 7 ft.*lbf }
4. Install the engine oil level dipstick.
CONNECT COOLER COMPRESSOR ASSEMBLY
1. Connect the cooler compressor assembly with the 2 stud bolts, 2 nuts and 2 bolts.
  
  Torque:
  
  for stud bolts
  
  10 N*m { 102 kgf*cm, 7 ft.*lbf }
  
  for nuts
  
  25 N*m { 255 kgf*cm, 18 ft.*lbf }
  
  for bolts
  
  25 N*m { 255 kgf*cm, 18 ft.*lbf }
INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH
1. Install a new gasket as shown in the illustration.
  
  Text in Illustration
  
  Front
2. Install the exhaust manifold to the cylinder head with the new 8 nuts in the order shown in the illustration.
  
  Torque:
  
  21 N*m { 214 kgf*cm, 15 ft.*lbf }
  
  Text in Illustration
  
  Front
INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
1. Install the heat insulator with the 3 bolts.
  
  Torque:
  
  10 N*m { 102 kgf*cm, 7 ft.*lbf }
2. Connect the sensor connector.
INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
1. Install the clamp to the steering column hole shield.
2. Text in Illustration
  
  *a Matchmark
  
  Align the matchmarks on the No. 2 steering intermediate shaft and steering column.
3. Install the bolt.
  
  Torque:
  
  35 N*m { 360 kgf*cm, 26 ft.*lbf }
INSTALL STEERING SLIDING YOKE WITH SHAFT SUB-ASSEMBLY (w/ VGRS)
1. Text in Illustration
  
  *a Matchmark
  
  Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering sliding with shaft yoke.
2. Align the matchmarks on the steering sliding with shaft yoke and power steering link.
3. Temporarily install bolt B.
  
  Note
  
  Do not tighten the bolt.
4. Text in Illustration
  
  *a Front of the vehicle
  
  Install bolt A and tighten bolt B.
  
  Torque:
  
  35 N*m { 360 kgf*cm, 26 ft.*lbf }
INSTALL STEERING SLIDING YOKE WITH SHAFT SUB-ASSEMBLY (w/o VGRS)
1. Text in Illustration
  
  *a Matchmark
  
  Align the matchmarks on the No. 2 steering intermediate shaft and steering sliding with shaft yoke.
2. Align the matchmarks on the steering sliding with shaft yoke and steering intermediate shaft.
3. Temporarily install bolt B.
  
  Note
  
  Do not tighten the bolt.
4. Text in Illustration
  
  *a Front of the vehicle
  
  Install bolt A and tighten bolt B.
  
  Torque:
  
  35 N*m { 360 kgf*cm, 26 ft.*lbf }
INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT LH
1. Install the front suspension member reinforcement LH to the vehicle with the 4 bolts.
  
  Torque:
  
  50 N*m { 510 kgf*cm, 37 ft.*lbf }
INSTALL FRONT STABILIZER BAR

Click here
INSTALL FRONT EXHAUST PIPE ASSEMBLY

Click here
CONNECT ENGINE WIRE
1. Connect the engine wire with the 4 nuts.
  
  Torque:
  
  10 N*m { 102 kgf*cm, 7 ft.*lbf }
2. Connect the clamp and install the 2 clamp brackets with the 2 bolts.
  
  Torque:
  
  10 N*m { 102 kgf*cm, 7 ft.*lbf }
3. Connect the intake air control valve actuator connector.
4. Connect the No. 1 vacuum switching valve connector.
5. Connect the ground wire with the bolt.
  
  Torque:
  
  21 N*m { 214 kgf*cm, 15 ft.*lbf }
6. for Engine Room RH Side:
  1. Connect the 2 clamps and install the 3 clamp brackets with the 3 bolts.
    
    Torque:
    
    10 N*m { 102 kgf*cm, 7 ft.*lbf }
  2. Connect the engine oil level sensor connector.
  3. Connect the crankshaft position sensor connector.
  4. Connect the starter connector and starter wire with the nut.
    
    Torque:
    
    10 N*m { 102 kgf*cm, 7 ft.*lbf }
  5. Connect the generator connector and generator wire with the nut.
    
    Torque:
    
    12 N*m { 122 kgf*cm, 9 ft.*lbf }
  6. Connect the camshaft position sensor connector.
  7. Connect the engine wire connector.
  8. Connect the 2 camshaft timing control motor connectors. (for Bank 2)
  9. Connect the 2 VVT sensor connectors.
  10. Connect the 4 ignition coil connectors.
  11. Connect the camshaft timing control valve connector.
  12. Connect the wires to the No. 1 engine room junction block with the 2 nuts.
    
    Torque:
    
    13 N*m { 133 kgf*cm, 10 ft.*lbf }
  13. Connect the 3 connectors to the front controller with the clamp.
7. for Engine Room LH Side:
  1. Install the clamp bracket with the bolt.
    
    Torque:
    
    10 N*m { 102 kgf*cm, 7 ft.*lbf }
  2. Connect the 3 clamps and 3 ground wires with the 3 bolts.
    
    Torque:
    
    10 N*m { 102 kgf*cm, 7 ft.*lbf }
  3. Attach the clamp and connect the cooler compressor connector.
  4. Connect the 2 camshaft timing control motor connectors. (for Bank 1)
  5. Connect the engine oil pressure sensor connector.
  6. Connect the engine coolant temperature sensor connector.
  7. Connect the clamp and install the 2 clamp brackets with the 2 bolts.
    
    Torque:
    
    10 N*m { 102 kgf*cm, 7 ft.*lbf }
  8. Connect the No. 8 engine wire connector.
  9. Connect the 2 VVT sensor connectors.
  10. Connect the 4 ignition coil connectors.
  11. Connect the camshaft timing control valve connector.
  12. Connect the 3 ECT connectors and 4 ECM connectors.
  13. Install the ECM box cover (upper).
INSTALL ENGINE ROOM ECU OUTLET DUCT
1. Install the engine room ECU outlet duct.
INSTALL SKID CONTROL ECU BRACKET

Click here
CONNECT NO. 2 RADIATOR HOSE
CONNECT NO. 1 RADIATOR HOSE
INSTALL V-RIBBED BELT
1. Install the V belt as shown in the illustration.
  
  Note
  
  Check that the drive belt is properly set to each pulley.
  1. Rotate the tensioner pulley counterclockwise, and then remove the fix bar.
INSTALL RADIATOR RESERVOIR ASSEMBLY
1. Install the radiator reservoir assembly with the 2 bolts.
  
  Torque:
  
  5.0 N*m { 51 kgf*cm, 44 in.*lbf }
2. Text in Illustration
  
  *a Upper
  
  Connect the 2 reservoir hoses.
  
  Tech Tips
  
  The direction of the hose clamp is indicated in the illustration.
INSTALL AIR CLEANER ASSEMBLY LH
1. Install the air cleaner case LH with the 2 nuts and clip.
  
  Torque:
  
  5.0 N*m { 51 kgf*cm, 44 in.*lbf }
2. Install the air cleaner element to the air cleaner case LH.
3. Install the air cleaner cap LH with the 2 clamps.
4. Connect the mass air flow meter connector.
INSTALL AIR CLEANER ASSEMBLY RH
1. Install the air cleaner case RH with the 2 nuts and clip.
  
  Torque:
  
  5.0 N*m { 51 kgf*cm, 44 in.*lbf }
2. Install the air cleaner element to the air cleaner case RH.
3. Install the air cleaner cap RH with the 2 clamps.
4. Connect the mass air flow meter connector.
INSTALL INTAKE AIR CONNECTOR PIPE
1. Align the protrusion of the intake air resonator with the cutout of the bracket and insert the protrusion.
2. Install the intake air connector pipe with the 3 hose clamps.
  
  Torque:
  
  for intake air connector pipe and throttle body
  
  4.8 N*m { 49 kgf*cm, 42 in.*lbf }
  
  for intake air connector pipe and air cleaner cap
  
  3.8 N*m { 39 kgf*cm, 34 in.*lbf }
  Tech Tips
  - Insert the protrusion of the intake air connector pipe into the hole of the hose clamp.
  - The intake air connector pipe and throttle body clamp can be tightened within the range of 4.0 N*m (41 kgf*cm, 35 in.*lbf) to 5.5 N*m (56 kgf*cm, 49 in.*lbf), and the intake air connector pipe and air cleaner cap clamp can be tightened within the range of 2.0 N*m (20 kgf*cm, 18 in.*lbf) to 5.5 N*m (56 kgf*cm, 49 in.*lbf).
3. Attach the 2 wire harness clamps.
4. Connect the No. 1 and No. 2 ventilation hoses to the intake air connector pipe.
  Tech Tips
  
  Position the claws of the clamps as shown in the illustration.
  
  Install the clamps so that they are within the hose's paint marks.
INSTALL NO. 1 AIR CLEANER INLET
1. Align the holes with the connection areas labeled A, and attach the No. 1 air cleaner inlet.
2. Install the No. 1 air cleaner inlet with the 2 bolts.
  
  Torque:
  
  5.0 N*m { 51 kgf*cm, 44 in.*lbf }
INSTALL ENGINE UNDER COVER REAR LH
1. Install the engine under cover rear LH with the 2 screws.
INSTALL ENGINE UNDER COVER REAR RH

Tech Tips

Install the RH side following the same procedures as the LH side.
INSTALL BATTERY TRAY
1. Install the battery tray with the 3 bolts.
  
  Torque:
  
  5.4 N*m { 55 kgf*cm, 48 in.*lbf }
2. Install the battery and battery insulator.
INSTALL BATTERY CLAMP SUB-ASSEMBLY
1. Install the battery clamp and 2 clamp bolts with the nut.
  
  Torque:
  
  5.4 N*m { 55 kgf*cm, 48 in.*lbf }

Text in Illustration
	Front

Text in Illustration
	Front

Text in Illustration
*a	Matchmark

Text in Illustration
*a	Matchmark

Text in Illustration
*a	Front of the vehicle

Text in Illustration
*a	Matchmark

Text in Illustration
*a	Front of the vehicle

Text in Illustration
*a	Upper

ADD ENGINE OIL

Add fresh oil.

Standard engine oil

Oil grade

Oil Viscosity (SAE)

API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving" or ILSAC multigrade engine oil

0W-20

5W-20

5W-30

10W-30

API grade SL, SM or SN multigrade engine oil

15W-40

20W-50

Standard capacity

Item	Specified Condition
Drain and refill without oil filter change	8.4 liters (8.9 US qts, 7.4 Imp. qts)
Drain and refill with oil filter change	8.6 liters (9.1 US qts, 7.6 Imp. qts)
Dry fill	10.2 liters (10.8 US qts, 9.0 Imp. qts)

Install the oil filler cap.
Close the oil filler cap service hole cover.

ADD ENGINE COOLANT
Total capacity

11.8 liters (12.5 US qts, 10.4 Imp. qts)

CAUTION:

Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot coolant and steam may be released and cause serious burns.

Note

Before adding coolant, turn the A/C switch off.
1. Tighten the radiator drain cock plug.
2. Tighten the 2 cylinder block drain cock plugs.
  
  Torque:
  
  13 N*m { 133 kgf*cm, 10 ft.*lbf }
3. Add TOYOTA Super Long Life Coolant (SLLC) into the radiator reservoir.
  
  Capacity
  
  Approximately 5.0 liters (5.3 US qts, 4.4 Imp. qts)
  Tech Tips
  - TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
  - Please contact any authorized Toyota dealer, or repairer or another duly qualified and equipped professional for further details.
  - The thermostat open timing can be confirmed by pressing the inlet radiator hose by hand, and checking when the coolant starts to flow inside the hose.
4. Further add coolant into the radiator reservoir until it reaches the FULL line.
5. Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the coolant level.
  
  If the coolant level is low, add coolant.
6. Using a 6 mm hexagon wrench, install the vent plug.
  
  Torque:
  
  1.5 N*m { 15 kgf*cm, 13 in.*lbf }
7. Bleed air from the cooling system.
  
  Note
  
  Before starting the engine to warm up the engine, turn the A/C switch off.
  1. While idling the engine for approximately 10 minutes, make sure the coolant remains at the FULL line by adding coolant as necessary.
  2. After idling the engine for 10 minutes, add coolant until it reaches the B line.
    
    Capacity
    
    Approximately 2.5 to 3.5 liters (2.6 to 3.7 US qts, 2.2 to 3.1 Imp. qts)
    
    Text in Illustration
    
    B Line
    
    Tech Tips
    
    The B line is the lower edge of the inner wall of the filler neck.
  3. Close the radiator reservoir cap, and run the engine at 1500 to 2000 rpm for 5 minutes.
    
    CAUTION:
    
    Wear protective gloves.
    
    Be careful as the radiator hose are hot.
    
    Keep your hands away from the radiator fans.
    
    Tech Tips
    
    The thermostat open timing can be confirmed by pressing the No. 1 radiator hose by hand, and checking when the SLLC starts to flow inside the hose.
8. Stop the engine and wait until the coolant cools down to ambient temperature.
9. Check the coolant level.
  
  If the coolant level is below the FULL line, add coolant until it reaches the FULL line.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
INSPECT FOR OIL LEAK
1. Start the engine. Make sure that there are no oil leaks from the area that was worked on.
INSPECT FOR COOLANT LEAK

CAUTION:

Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

Note

Before each inspection, turn the A/C switch OFF.
1. Fill the radiator with coolant and attach a radiator cap tester.
2. Warm up the engine.
3. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm², 17 psi), and check that the pressure does not drop.
  
  If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.
INSPECT FOR EXHAUST GAS LEAK
1. If gas is leaking, tighten the areas necessary to stop the leak. Replace the damaged parts as necessary.
CHECK ENGINE OIL LEVEL
1. Warm up the engine, stop the engine and wait 5 minutes. The oil level should be between the dipstick's low level mark and full level mark.
  
  If low, check for leakage and add oil up to the full level mark.
  
  Note
  
  Do not fill engine oil above the full level mark.
  Tech Tips
  
  A certain amount of engine oil will be consumed while driving. In the following situations, oil consumption may increase, and engine oil may need to be refilled in between oil maintenance intervals.
  - When the engine is new, for example directly after purchasing the vehicle or after replacing the engine.
  - If low quality oil or oil of an inappropriate viscosity is used.
  - When driving at high engine speed or with a heavy load, (when towing, or), when driving while accelerating or decelerating frequently.
  - When leaving the idling for a long time, or when driving frequently through heavy traffic.
  When judging the amount of oil consumption, keep in mind that the oil may have become diluted, making it difficult to judge the true level accurately.
INSTALL FRONT SUSPENSION MEMBER PROTECTOR LOWER
1. Install the front suspension member protector lower with the 8 bolts.
  
  Torque:
  
  5.5 N*m { 56 kgf*cm, 49 in.*lbf }
INSTALL NO. 2 ENGINE UNDER COVER
1. Install the No. 2 engine under cover with the 8 bolts.
  
  Torque:
  
  for Bolt A
  
  10 N*m { 102 kgf*cm, 7 ft.*lbf }
  
  for Bolt B
  
  27 N*m { 275 kgf*cm, 20 ft.*lbf }
INSTALL NO. 1 ENGINE UNDER COVER
1. Install the No. 1 engine under cover with the 13 screws and 7 clips.
INSTALL ENGINE ROOM SIDE COVER RH
1. Install the engine room side cover RH with the 5 clips.
INSTALL ENGINE ROOM SIDE COVER LH
1. Install the engine room side cover LH with the 5 clips.
INSTALL AIR CLEANER INLET COVER SUB-ASSEMBLY
1. Attach the 4 clips B.
  Note
  - Make sure the clips are attached securely.
  - Attaching the clips forcefully or hitting the top of the clips may damage them.
2. Install the air cleaner inlet cover sub-assembly with the 5 clips labeled A.
INSTALL V-BANK COVER SUB-ASSEMBLY
1. After sliding the cover from the vehicle front to the rear to attaching the 2 clips labeled A, attach the 4 clips labeled B and install the V-bank cover sub-assembly.
  Note
  - Make sure the clips are attached securely.
  - Attaching the clips forcefully or hitting the top of the clips may damage them.
INSTALL COWL TOP VENTILATOR LOUVER RH
1. Install the 6 clips and cowl top ventilator louver RH.
  
  Note
  
  If the cowl top ventilator louver RH is not properly installed, water may leak into the engine room and cause malfunctions. Therefore, make sure the cowl top ventilator louver RH is installed properly.