COOLING FAN MOTOR (for 2WD) REMOVAL


  1. REMOVE V-BANK COVER SUB-ASSEMBLY


    1. A01GMKRE01

      Using both hands, lift the rear side of the cover upwards to detach the 4 clips labeled B. Then slide the cover toward the front of the vehicle to detach the 2 clips labeled A and remove the V-bank cover sub-assembly.

      Note


      • The V-bank cover sub-assembly may be damaged if its front and rear are lifted at the same time.

      • When detaching the clips labeled A, be sure to slide the cover toward the front of the vehicle.

  2. REMOVE AIR CLEANER INLET COVER SUB-ASSEMBLY


    1. A01GLYAE01

      Remove the 5 clips labeled A.

    2. Lift up the air cleaner inlet cover sub-assembly to detach the 4 clips labeled B, and remove the air cleaner inlet cover sub-assembly.

  3. REMOVE NO. 1 AIR CLEANER INLET


    1. A01GKZB

      Remove the 2 bolts.

    2. A01GJVME01

      Hold the No. 1 air cleaner inlet by the protrusions labeled A and labeled B, and detach the connections.

    3. Rotate the No. 1 air cleaner inlet as shown in the illustration to detach the protrusion labeled C.

    4. Hold the No. 1 air cleaner inlet by the protrusions labeled D and labeled E, and detach the connections.

    5. Rotate the No. 1 air cleaner inlet as shown in the illustration to detach the protrusion labeled F.

  4. REMOVE ENGINE ROOM SIDE COVER RH


    1. A01GL9VE01
      Text in Illustration
      *A for LHD
      *B for RHD

      Remove the 5 clips and engine room side cover RH.

  5. REMOVE ENGINE ROOM SIDE COVER LH


    1. A01GK7CE01
      Text in Illustration
      *A for LHD
      *B for RHD

      Remove the 5 clips and engine room side cover LH.

  6. REMOVE NO. 1 ENGINE UNDER COVER


    1. A01GHO1E01
      Text in Illustration
      *A for 2WD
      *B for AWD

      Remove the 13 screws, 7 clips and No. 1 engine under cover.

  7. DRAIN ENGINE COOLANT

    CAUTION:

    Do not remove the radiator reservoir cap and vent plug while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


    1. Loosen the radiator drain cock plug.

      A01GLBYE01
      Text in Illustration
      *1 Radiator Drain Cock Plug *2 Radiator Reservoir Cap
      *3 Vent Plug *4 Cylinder Block Drain Cock Plug

      Tech Tips

      Collect the coolant in a container and dispose of it according to the regulations in your area.

    2. A01GN7SE02
      Text in Illustration
      *1 Vent Plug

      Remove the radiator reservoir cap, and using a 6 mm hexagon wrench, remove the vent plug.

    3. Drain coolant.

    4. Loosen the 2 cylinder block drain cock plugs.

  8. REMOVE NO. 1 RADIATOR HOSE


    1. A01GJM7

      Remove the No. 1 radiator hose.

  9. REMOVE NO. 2 RADIATOR HOSE


    1. A01GMF9

      Remove the No. 2 radiator hose.

  10. REMOVE ENGINE ROOM ECU OUTLET DUCT


    1. A01GJC3

      Remove the engine room ECU outlet duct.

  11. REMOVE RADIATOR RESERVOIR ASSEMBLY


    1. A01GI8P

      Disconnect the 2 reservoir hoses.

    2. Remove the 2 bolts and radiator reservoir assembly.

  12. DISCONNECT WIRE HARNESS


    1. A01GNYS

      Disconnect the 3 connectors.

    2. Detach the 8 wire harness clamps to disconnect the wire harness.

  13. REMOVE FAN SHROUD WITH FAN AND MOTOR


    1. A01GNG2

      Detach the 3 claws, and then remove the fan shroud with fan and motor.