PURGE VALVE INSTALLATION


  1. INSTALL PURGE VSV


    1. A01GKVX

      Install the purge VSV with the bolt.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

    2. Connect the 2 purge line hoses to the purge VSV.

    3. Connect the purge VSV connector.

  2. CONNECT ENGINE WIRE (for LHD)


    1. A01GN6Q

      Connect the cooler compressor connector.

    2. Connect the wire harness bracket with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }
    3. A01GMGL

      Install the clamp bracket with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    4. Connect the 3 clamps and 3 ground wires with the 3 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    5. Connect the 2 camshaft timing control motor connectors (for Bank 1).

    6. Connect the oil pressure sensor connector.

    7. Connect the engine coolant temperature sensor connector.

    8. A01GHJ5

      Connect the clamp and install the 2 clamp brackets with the 2 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    9. Connect the No. 8 engine wire connector.

    10. Connect the fuel pump connector (for high pressure).

    11. Connect the 2 VVT sensor connectors.

    12. Connect the 4 ignition coil connectors.

    13. Connect the camshaft timing control valve connector.

    14. for AWD:


      1. Connect the engine wire harness with the 4 nuts.

        Torque:
        10 N*m  { 102 kgf*cm, 7 ft.*lbf }
        A01GICUE01

      2. Install the 2 engine wire harness clamp brackets with the 2 bolts.

        Torque:
        10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      3. Connect the engine wire to the fusible link block assembly with the nut.

        Torque:
        13 N*m  { 127 kgf*cm, 10 ft.*lbf }

      4. Connect the engine wire harness to the +B terminal of the generator assembly with the nut.

        Torque:
        12 N*m  { 122 kgf*cm, 9 ft.*lbf }

      5. Connect the 6 engine wire harness clamps.

      6. Connect the engine wire harness connectors.

        Tech Tips

        To connect the injector driver connectors, move the lock lever to lock the connector.

    15. for 2WD:


      1. Connect the engine wire harness with the 4 nuts.

        Torque:
        10 N*m  { 102 kgf*cm, 7 ft.*lbf }
        A01GLSTE01

      2. Install the 3 engine wire harness clamp brackets with the 3 bolts.

        Torque:
        10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      3. Connect the engine wire to the fusible link block assembly with the nut.

        Torque:
        13 N*m  { 127 kgf*cm, 9 ft.*lbf }

      4. Connect the engine wire harness to the +B terminal of the generator assembly with the nut.

        Torque:
        12 N*m  { 122 kgf*cm, 9 ft.*lbf }

      5. Connect the 7 engine wire harness clamps.

      6. Connect the engine wire harness connectors.

        Tech Tips

        To connect the injector driver connectors, move the lock lever to lock the connector.

  3. CONNECT ENGINE WIRE (for RHD)


    1. A01GN6Q

      Connect the cooler compressor connector.

    2. Connect the wire harness bracket with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }
    3. A01GMGL

      Install the clamp bracket with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    4. Connect the 3 clamps and 3 ground wires with the 3 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    5. Connect the 2 camshaft timing control motor connectors (for Bank 1).

    6. Connect the oil pressure sensor connector.

    7. Connect the engine coolant temperature sensor connector.

    8. A01GMD8

      Connect the engine wire to the fusible link block assembly with the nut.

      Torque:
      13 N*m  { 127 kgf*cm, 9 ft.*lbf }

    9. Attach the 3 wire harness clamps.

    10. Connect the clamp and install the 2 clamp brackets with the 2 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    11. Connect the No. 8 engine wire connector.

    12. Connect the fuel pump connector (for high pressure).

    13. Connect the 2 VVT sensor connectors.

    14. Connect the 4 ignition coil connectors.

    15. Connect the camshaft timing control valve connector.

    16. Connect the engine wire harness with the 4 nuts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }
      A01GLC0E02

    17. Install the 3 engine wire harness clamp brackets with the 3 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    18. Connect the 5 engine wire harness clamps.

    19. Connect the engine wire harness to the +B terminal of the generator assembly with the nut.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

    20. Connect the engine wire harness connectors.

      Tech Tips

      To connect the injector driver connectors, move the lock lever to lock the connector.

  4. INSTALL AIR CLEANER CAP SUB-ASSEMBLY LH


    1. A01GL3TE02

      Install the air cleaner cap sub-assembly LH to the air cleaner case with the 2 clips.

      Torque:
      for hose clamp
      3.8 N*m  { 39 kgf*cm, 34 in.*lbf }

      Tech Tips

      Insert the protrusion of the air cleaner hose into the hole of the hose clamp.

    2. Connect the mass air flow meter connector.

  5. INSTALL AIR CLEANER CAP SUB-ASSEMBLY RH


    1. A01GI75E02

      Install the air cleaner cap sub-assembly RH to the air cleaner case with the 2 clips.

      Torque:
      for hose clamp
      3.8 N*m  { 39 kgf*cm, 34 in.*lbf }

      Tech Tips

      Insert the protrusion of the air cleaner hose into the hole of the hose clamp.

    2. Connect the mass air flow meter connector.

  6. INSTALL INTAKE AIR CONNECTOR PIPE


    1. Install the intake air sound creator.

      Tech Tips

      Only perform this procedure when replacement of the intake air sound creator is necessary.


      1. Install the intake air sound creator with the bolt and hose clamp.

        Torque:
        2.0 N*m  { 20 kgf*cm, 18 in.*lbf }

    2. Align the protrusion of the intake air resonator with the cutout of the bracket and insert the protrusion.

    3. Install the intake air connector pipe with the 3 hose clamps.

      Torque:
      for intake air connector pipe and throttle body
      4.8 N*m  { 49 kgf*cm, 42 in.*lbf }
      for intake air connector pipe and air cleaner cap
      3.8 N*m  { 39 kgf*cm, 34 in.*lbf }

      Tech Tips


      • Insert the protrusion of the intake air connector pipe into the hole of the hose clamp.

      • The intake air connector pipe and throttle body clamp can be tightened within the range of 4.0 N*m (41 kgf*cm, 35 in.*lbf) to 5.5 N*m (56 kgf*cm, 49 in.*lbf), and the intake air connector pipe and air cleaner cap clamp can be tightened within the range of 2.0 N*m (20 kgf*cm, 18 in.*lbf) to 5.5 N*m (56 kgf*cm, 49 in.*lbf).

    4. Attach the 2 wire harness clamps.

    5. A01GMMEE03

      Connect the No. 1 and No. 2 ventilation hoses to the intake air connector pipe.

      Tech Tips


      • Position the claws of the clamps as shown in the illustration.

      • Install the clamps so that they are within the hose's paint marks.

  7. INSTALL NO. 1 AIR CLEANER INLET


    1. A01GIR0E02

      Align the holes with the connection areas labeled A, and attach the No. 1 air cleaner inlet.

    2. Install the No. 1 air cleaner inlet with the 2 bolts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  8. INSTALL V-BANK COVER SUB-ASSEMBLY


    1. A01GMKRE01

      Slide the cover from the vehicle front toward the rear of the vehicle to attach the 2 clips labeled A, and then attach the 4 clips labeled B to install the V bank cover sub-assembly.

      Note


      • Make sure the clips are attached securely.

      • Attaching the clips forcefully or hitting the top of the clips may damage them.

      • When attaching the clips labeled A, be sure to slide the cover from the front of the vehicle toward the rear of the vehicle.

  9. INSTALL ENGINE ROOM SIDE COVER LH


    1. Install the engine room side cover LH with the 5 clips.

  10. INSTALL ENGINE ROOM SIDE COVER RH


    1. Install the engine room side cover RH with the 5 clips.

  11. INSTALL AIR CLEANER INLET COVER SUB-ASSEMBLY


    1. A01GLYAE01

      Attach the 4 clips labeled B.

      Note


      • Make sure the clips are attached securely.

      • Attaching the clips forcefully or hitting the top of the clips may damage them.

    2. Install the air cleaner inlet cover sub-assembly with the 5 clips labeled A.