BLOCKING SYSTEM, Diagnostic DTC:B1586

DTC Code DTC Name
B1586 Open in Immobiliser Communication Circuit

DESCRIPTION

When the communication line (EFIO - BLK4) between the ID code box (immobiliser code ECU) and telephone transceiver assembly is open, the telephone transceiver assembly stores DTC B1586.

DTC Code DTC Detection Condition Trouble Area
B1586 The communication line (EFIO - BLK4) between the ID code box (immobiliser code ECU) and telephone transceiver assembly is open.

  • Telephone transceiver assembly

  • ID code box (immobiliser code ECU)

  • Harness or connector

WIRING DIAGRAM

A01GMWJE05

INSPECTION PROCEDURE

Note


  • Before troubleshooting for this DTC, make sure no immobiliser system DTCs are present. If present, troubleshoot the immobiliser system DTCs first.

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

  • When replacing the telephone transceiver assembly or ID code box (immobiliser code ECU), refer to the Service Bulletin.

  • When the telephone transceiver assembly is replaced, it is necessary to set the contract mode.

PROCEDURE


  1. CHECK FOR DTC


    1. Clear the DTCs Click here.

    2. Turn the engine switch off.

    3. Turn the engine switch on (IG).

    4. After 10 seconds have elapsed, check for DTCs.

      OK
      DTC B1586 is not output.
      Result
      Result Proceed to
      DTC is not output. A
      Only DTC B1586 is output. B
      DTC B1586 and other DTCs are output. C

    B

    CHECK CONNECTION OF CONNECTORS Click here

    C

    GO TO DIAGNOSTIC TROUBLE CODE CHART Click here

    A

    USE SIMULATION METHOD TO CHECK Click here

  2. CHECK CONNECTION OF CONNECTORS


    1. Turn the engine switch off.

    2. Check that the connectors are properly connected to the telephone transceiver assembly and ID code box (immobiliser code ECU).

      OK
      Connectors are properly connected.

    NG

    CONNECT CONNECTORS CORRECTLY

    OK

  3. CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - ID CODE BOX [IMMOBILISER CODE ECU])


    1. Disconnect the L180 telephone transceiver assembly connector.

    2. Disconnect the L32 ID code box (immobiliser code ECU) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L180-2 (BLK4) - L32-6 (EFIO) Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK ID CODE BOX (IMMOBILISER CODE ECU) (OUTPUT)


    1. Reconnect the L180 telephone transceiver assembly connector.

    2. Reconnect the L32 ID code box (immobiliser code ECU) connector.

    3. Using an oscilloscope, check the waveform.

      Note

      The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

      A01GN4TE03
      Text in Illustration
      *a

      Component with harness connected

      (ID Code Box [Immobiliser Code ECU])

      		 *b Approximately 160 ms.
      *c Approximately 270 ms. - -
      Measurement Condition
      Item Content
      Tester Connection L32-6 (EFIO) - L32-8 (GND)
      Tool Setting 2 V/DIV., 500 ms./DIV.
      Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected

      Tech Tips

      The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

      OK
      The waveform is output normally (refer to illustration).

    NG

    CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - BATTERY AND BODY GROUND) Click here

    OK

    REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

  5. CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - BATTERY AND BODY GROUND)


    1. A01GNJWE07
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Telephone Transceiver Assembly)

      Disconnect the L180 telephone transceiver assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L180-9 (E) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      L180-12 (+B) - Body ground Always 11 to 14 V
      L180-6 (IG2) - Body ground Engine switch off Below 1 V
      L180-6 (IG2) - Body ground Engine switch on (IG) 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. REPLACE ID CODE BOX (IMMOBILISER CODE ECU)


    1. Temporarily replace the ID code box (immobiliser code ECU) with a new one.

      Tech Tips

      Refer to the Service Bulletin.


    NEXT

  7. PERFORM REGISTRATION


    1. Perform the registration.

      Tech Tips

      Refer to the Service Bulletin.


    NEXT

  8. CHECK FOR DTC


    1. Clear the DTCs Click here.

    2. Turn the engine switch off.

    3. Turn the engine switch on (IG).

    4. After 10 seconds have elapsed, check for DTCs.

      OK
      DTC B1586 is not output.

    NG

    REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

    OK

    END (ID CODE BOX [IMMOBILISER CODE ECU] WAS DEFECTIVE)