THEFT DETERRENT SYSTEM Security Indicator Light Circuit

DESCRIPTION

• When the theft deterrent system is in the disarmed state, the security indicator will flash continuously if the immobiliser system is set, or not illuminate if the immobiliser system is not set.

  When the theft deterrent system is in the armed state, the immobiliser system is automatically set and the security indicator will flash continuously.

  When the theft deterrent system is in the arming preparation state and alarm sounding state, the certification ECU causes the security indicator to be illuminated.

WIRING DIAGRAM

INSPECTION PROCEDURE

PROCEDURE

1. CHECK INDICATOR LIGHT ASSEMBLY

   
   

   1. Check if the security indicator lights are normal.

      Result

      Result	Proceed to
      One security indicator light is malfunctioning	A
      Both security indicator lights are malfunctioning	B

      Tech Tips

      If both security indicator lights are malfunctioning, there may be a malfunction in the certification ECU.

   
   

   B

   REPLACE CERTIFICATION ECU

   A

2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR)

   
   

   1. Operate the intelligent tester according to the steps on the display and select "Active Test".

      
      

      1. Intelligent tester

         Entry&Start

         Tester Display	Test Part	Control Range
         Security Indicator	Security indicator	ON / OFF

         OK
         Security indicator illuminates.

   
   

   NG

   CHECK HARNESS AND CONNECTOR (DOOR ECU - SECURITY INDICATOR) Click here

   OK

   REPLACE CERTIFICATION ECU

3. CHECK HARNESS AND CONNECTOR (DOOR ECU - SECURITY INDICATOR)

   

   
   

   1. Disconnect the P10*1 or P4*2 ECU connector.

   2. Disconnect the P9*1 or P3*2 indicator connector.

   3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      for LH Tester Connection Condition Specified Condition P10-8 (SID+) - P9-2 (LP2) Always Below 1 Ω P10-9 (SID-) - P9-1 (E2) Always Below 1 Ω P10-8 (SID+) or P9-2 (LP2) - Body ground Always 10 kΩ or higher P10-9 (SID-) or P9-1 (E2) - Body ground Always 10 kΩ or higher
      for RH Tester Connection Condition Specified Condition P4-8 (SID+) - P3-2 (LP1) Always Below 1 Ω P4-9 (SID-) - P3-1 (E1) Always Below 1 Ω P4-8 (SID+) or P3-2 (LP1) - Body ground Always 10 kΩ or higher P4-9 (SID-) or P3-1 (E1) - Body ground Always 10 kΩ or higher

   
   

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR

   OK

4. CHECK HARNESS AND CONNECTOR (DOOR ECU - CERTIFICATION ECU AND BODY GROUND)

   

   
   

   1. Disconnect the N10*1 or N1*2 ECU connector.

   2. Disconnect the L15 ECU connector.

   3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      for LH Tester Connection Condition Specified Condition N10-23 (SID1) - L15-2 (IND) Always Below 1 Ω N10-1 (GND) - Body ground Always Below 1 Ω N10-23 (SID1) or L15-2 (IND) - Body ground Always 10 kΩ or higher
      for RH Tester Connection Condition Specified Condition N1-23 (SID1) - L15-2 (IND) Always Below 1 Ω N1-1 (GND) - Body ground Always Below 1 Ω N1-23 (SID1) or L15-2 (IND) - Body ground Always 10 kΩ or higher

   
   

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR

   OK

5. INSPECT INDICATOR LIGHT ASSEMBLY

   
   

   1. 

      Remove the indicator light Click here.

   2. Check operation of the indicator light.

      OK
      Measurement Condition Specified Condition Battery positive (+) → Terminal 2 (LP2*1, LP1*2) Battery positive (+) → Terminal 1 (E) Illuminates

      Note

      
      

      • If the positive (+) lead and the negative (-) lead are incorrectly connected, the security indicator will not turn on.

      • A voltage of more than 12 V will damage the security indicator.

      • If the voltage is too low, the security indicator will not turn on.

   
   

   NG

   REPLACE INDICATOR LIGHT ASSEMBLY

   OK

6. CHECK FRONT DOOR ECU (OPERATION)

   
   

   1. Temporarily replace the front door ECU with a new or normally functioning one Click here.

   2. Check that the security indicator operates normally.

      OK
      Security indicator operates normally.

   
   

   NG

   REPLACE CERTIFICATION ECU

   OK

   REPLACE FRONT DOOR ECU