БЛОК ДВИГАТЕЛЯ ПРОВЕРКА


  1. INSPECT BALANCESHAFT THRUST CLEARANCE


    1. Install the balanceshafts Click here.

    2. A01CEDB

      Using a dial indicator, measure the thrust clearance while moving the balanceshaft back and forth.

      Standard thrust clearance
      0.05 to 0.09 mm (0.00197 to 0.00354 in.)
      Maximum thrust clearance
      0.09 mm (0.00354 in.)

      If the thrust clearance is greater than the maximum, replace the balanceshaft housing and bearings. If necessary, replace the balanceshaft.

  2. INSPECT BALANCESHAFT OIL CLEARANCE


    1. Clean each bearing and journal.

    2. Check each bearing and journal for pitting and scratches.

      If a bearing or journal is damaged, replace the bearings. If necessary, replace the balanceshaft.

    3. Place the No. 1 and No. 2 balanceshafts onto the crankcase.

    4. A01CFQRE02
      Text in Illustration
      *1 Plastigage

      Lay a strip of Plastigage across each journal.

    5. Install the balanceshaft housing Click here.

      Note

      Do not turn the balanceshafts.

    6. Remove the balanceshafts Click here.

    7. A01CDOVE03
      Text in Illustration
      *1 Plastigage

      Measure the Plastigage at its widest point.

      Standard oil clearance
      0.022 to 0.049 mm (0.000866 to 0.00193 in.)
      Maximum oil clearance
      0.049 mm (0.00193 in.)

      Note

      Remove the Plastigage completely after the measurement.

      If the oil clearance is greater than the maximum, replace the bearing. If necessary, replace the balanceshaft.

    8. A01CAW0E02
      Text in Illustration
      *a Number Mark
      *b Front No. 1 Journal Bore
      *c Rear No. 1 Journal Bore
      *d Front No. 2 Journal Bore
      *e Rear No. 2 Journal Bore

      If replacing a bearing, select a new one with the same number.

      Standard Balanceshaft Housing Journal Bore Diameter
      Item Specified Condition
      Mark 1 26.000 to 26.006 mm (1.0236 to 1.0239 in.)
      Mark 2 26.007 to 26.012 mm (1.0239 to 1.0241 in.)
      Mark 3 26.013 to 26.018 mm (1.0241 to 1.0243 in.)
      Standard Bearing Center Wall Thickness
      Item Specified Condition
      Mark 1 1.486 to 1.489 mm (0.05850 to 0.05862 in.)
      Mark 2 1.490 to 1.492 mm (0.05866 to 0.05874 in.)
      Mark 3 1.493 to 1.495 mm (0.0588 to 0.0589 in.)
      Standard balanceshaft journal diameter
      22.985 to 23.000 mm (0.9049 to 0.9055 in.)

    9. Inspect the balanceshaft housing bolts.


      1. A01CG42E05
        Text in Illustration
        *a Measurement Length

        Using a vernier caliper, measure the length of the bolts from the seat to the end.

        Standard bolt length
        58.3 to 59.7 mm (2.295 to 2.350 in.)
        Maximum bolt length
        60.3 mm (2.374 in.)

        If the bolt length is greater than the maximum, replace the balanceshaft housing bolt.

  3. INSPECT CHAIN SUB-ASSEMBLY


    1. A01CCKEE10
      Text in Illustration
      *a Measurement Area

      Pull the chain with a force of 140 N (14 kgf, 31.5 lbf) as shown in the illustration.

    2. Using a vernier caliper, measure the length of 15 links.

      Maximum chain elongation
      114.5 mm (4.508 in.)

      Note

      Perform the measurement at 3 random places. Use the average of the measurements.

      If the elongation is greater than the maximum, replace the chain.

  4. INSPECT NO. 2 CHAIN SUB-ASSEMBLY


    1. A01CCKEE10
      Text in Illustration
      *a Measurement Area

      Pull the chain with a force of 140 N (14 kgf, 31.5 lbf) as shown in the illustration.

    2. Using a vernier caliper, measure the length of 15 links.

      Maximum chain elongation
      102.2 mm (4.024 in.)

      Note

      Perform the measurement at 3 random places. Use the average of the measurements.

      If the elongation is greater than the maximum, replace the No. 2 chain.

  5. INSPECT OIL PUMP DRIVE GEAR


    1. A01CEW1E01

      Place the chain around the sprocket.

    2. Using a vernier caliper, measure the sprocket diameter of the oil pump drive gear and chain.

      Minimum gear diameter (with chain)
      48.2 mm (1.898 in.)

      Note

      The vernier caliper must be in contact with the chain rollers when measuring.

      If the diameter is less than the minimum, replace the chain and sprocket.

  6. INSPECT OIL PUMP DRIVE SHAFT GEAR


    1. A01CAJQE01

      Place the chain around the sprocket.

    2. Using a vernier caliper, measure the sprocket diameter of the oil pump drive shaft gear and chain.

      Minimum gear diameter (with chain)
      48.2 mm (1.898 in.)

      Note

      The vernier caliper must be in contact with the chain rollers when measuring.

      If the diameter is less than the minimum, replace the chain and sprocket.

  7. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY


    1. A01CBMD

      Place the chain around the sprocket.

    2. Using a vernier caliper, measure the sprocket diameter of the camshaft timing gear assembly and chain.

      Minimum gear diameter (with chain)
      97.3 mm (3.831 in.)

      Note

      The vernier caliper must be in contact with the chain rollers when measuring.

      If the diameter is less than the minimum, replace the chain and sprocket.

  8. INSPECT CAMSHAFT TIMING GEAR OR SPROCKET


    1. A01CEMX

      Place the chain around the sprocket.

    2. Using a vernier caliper, measure the sprocket diameter of the camshaft timing gear or sprocket and chain.

      Minimum gear diameter (with chain)
      97.3 mm (3.831 in.)

      Note

      The vernier caliper must be in contact with the chain rollers when measuring.

      If the diameter is less than the minimum, replace the chain and sprocket.

  9. INSPECT CRANKSHAFT TIMING GEAR OR SPROCKET


    1. A01CEW1E01

      Place the chain around the timing sprocket.

    2. Using a vernier caliper, measure the timing gear diameter of the camshaft timing gear or sprocket and chain.

      Minimum gear diameter (with chain)
      51.6 mm (2.031 in.)

      Note

      The vernier caliper must be in contact with the chain rollers when measuring.

      If the gear diameter is less than the minimum, replace the chain sub-assembly and crankshaft timing sprocket.

  10. INSPECT CHAIN TENSIONER SLIPPER


    1. A01CEXIE01

      Using a vernier caliper, measure the tensioner slipper wear.

      Maximum wear
      1.0 mm (0.0394 in.)

      If the wear is greater than the maximum, replace the chain tensioner slipper.

  11. INSPECT NO. 1 CHAIN VIBRATION DAMPER


    1. A01CASWE01

      Using a vernier caliper, measure the vibration damper wear.

      Maximum wear
      1.0 mm (0.0394 in.)

      If the wear is greater than the maximum, replace the No. 1 chain vibration damper.

  12. INSPECT CHAIN TENSIONER PLATE


    1. A01CCLV

      Using a vernier caliper, measure the chain tensioner plate wear.

      Maximum wear
      0.5 mm (0.0197 in.)

      If the wear is greater than the maximum, replace the chain tensioner plate.

  13. INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY


    1. A01CF3DE05
      Text in Illustration
      *a Raise
      *b Move
      *c Lock

      Check that the plunger moves smoothly when the ratchet pawl is raised with your finger.

    2. Release the ratchet pawl, then check that the plunger is locked in place by the ratchet pawl and does not move when pushed with your finger.

      If operation is not as specified, replace the No. 1 chain tensioner assembly.

  14. INSPECT CAMSHAFT


    1. A01CC4AE01

      Inspect the camshaft for runout.


      1. Place the camshaft on V-blocks.

      2. Using a dial indicator, measure the circle runout at the center journal.

        Maximum circle runout
        0.03 mm (0.00118 in.)

        If the circle runout is greater than the maximum, replace the camshaft.

    2. A01CENXE01

      Inspect the cam lobes.


      1. Using a micrometer, measure the cam lobe heights.

        Standard cam lobe height
        47.306 to 47.406 mm (1.8624 to 1.8664 in.)
        Minimum cam lobe height
        47.196 mm (1.8581 in.)

        If any of the cam lobe heights are less than the minimum, replace the camshaft.

    3. A01CB8OE01

      Inspect the camshaft journals.


      1. Using a micrometer, measure the journal diameter.

        Standard Journal Diameter
        Journal Position Specified Condition
        No. 1 35.971 to 35.985 mm (1.4162 to 1.4167 in.)
        Others 22.959 to 22.975 mm (0.9039 to 0.9045 in.)

        If the journal diameter is not as specified, check the oil clearance.

  15. INSPECT NO. 2 CAMSHAFT


    1. A01CC4AE01

      Inspect the camshaft for runout.


      1. Place the camshaft on V-blocks.

      2. Using a dial indicator, measure the circle runout at the center journal.

        Maximum circle runout
        0.03 mm (0.00118 in.)

        If the circle runout is greater than the maximum, replace the No. 2 camshaft.

    2. A01CENXE01

      Inspect the cam lobes.


      1. Using a micrometer, measure the cam lobe heights.

        Standard cam lobe height
        46.063 to 46.163 mm (1.8135 to 1.8174 in.)
        Minimum cam lobe height
        45.953 mm (1.8092 in.)

        If any of the cam lobe heights are less than the minimum, replace the No. 2 camshaft.

    3. A01CB8OE01

      Inspect the camshaft journals.


      1. Using a micrometer, measure the journal diameter.

        Standard Journal Diameter
        Journal Position Specified Condition
        No. 1 35.971 to 35.985 mm (1.4162 to 1.4167 in.)
        Others 22.959 to 22.975 mm (0.9039 to 0.9045 in.)

        If the journal diameter is not as specified, check the oil clearance.