СИСТЕМА SFI, Diagnostic DTC:P0504

DTC Code DTC Name
P0504 Brake Switch "A" / "B" Correlation

DESCRIPTION

The stop light switch assembly is a duplex system that transmits 2 signals: STP and ST1-. These 2 signals are used by the ECM to monitor whether or not the brake system is working properly. If both signals, which indicate the brake pedal is being depressed or released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and sets the DTC.

DTC No. DTC Detection Condition Trouble Area
P0504

Conditions (a) and (b) continue for 0.5 seconds or more

(1 trip detection logic):

(a) Engine switch is on (IG)

(b) STP signal is off when ST1- signal is off

  • Open or short in stop light switch signal circuit

  • Stop light switch assembly

  • STOP fuse

  • ECM

WIRING DIAGRAM

A01CDD0E10

INSPECTION PROCEDURE

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

Tech Tips


  • Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

  • STP signal conditions can be checked using the intelligent tester.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the tester on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Stop Light Switch.

    5. Check the STP signal when the brake pedal is depressed and released.

      Brake Pedal Operation Specified Condition
      Depressed STP signal on
      Released STP signal off

PROCEDURE


  1. CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE)


    1. A01CE90E36
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Stop Light Switch Assembly)

      Disconnect the stop light switch assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A1-2 - Body ground Always 11 to 14 V

    3. Reconnect the stop light switch assembly connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY)

    OK

  2. CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE)


    1. A01CE90E36
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Stop Light Switch Assembly)

      Disconnect the stop light switch assembly connector.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      A1-4 - Body ground Engine switch on (IG) 11 to 14 V

    4. Reconnect the stop light switch assembly connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - IG2 RELAY)

    OK

  3. INSPECT STOP LIGHT SWITCH ASSEMBLY


    1. A01CEADE02

      Remove the stop light switch assembly.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Position Specified Condition
      1 - 2 Switch pin not pushed Below 1 Ω
      Switch pin pushed 10 kΩ or higher
      3 - 4 Switch pin not pushed 10 kΩ or higher
      Switch pin pushed Below 1 Ω

    3. Reinstall the stop light switch assembly.


    NG

    REPLACE STOP LIGHT SWITCH ASSEMBLY Click here

    OK

  4. CHECK ECM (STP AND ST1- VOLTAGE)


    1. Disconnect the ECM connector.

      A01CFHOE08

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A8-35 (ST1-) - Body ground Brake pedal released 7.5 to 14 V
      Brake pedal depressed 0 to 1.5 V
      A8-36 (STP) - Body ground Brake pedal released 0 to 1.5 V
      Brake pedal depressed 7.5 to 14 V

    4. Reconnect the ECM connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)

    OK

    REPLACE ECM Click here