СИСТЕМА SFI, Diagnostic DTC:P0500

DTC Code DTC Name
P0500 Vehicle Speed Sensor "A"

DESCRIPTION

The wheel speed sensors monitor the wheel rotation speed and send signals to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter assembly. The ECM determines the vehicle speed based on the frequency of the pulse signal.

Tech Tips


  • A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.

  • If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the wiring diagram below will not operate normally.

A01CC7TE40
DTC No. DTC Detection Condition Trouble Area
P0500

for CVT models:

Either of the following conditions (a) and (b) is met for 2.0 seconds or more

(1 trip detection logic)

(a) Transmission revolution sensor signal output is 1000 rpm or more

(b) No vehicle speed sensor signal to ECM

for A/T models:

Either of the following conditions (A) and (B) are met

(1 trip detection logic)

(A) Either of the following conditions 1or 2 is met


  1. All of the following conditions (a), (b) and (c) are met


    1. Engine coolant temperature is 20°C (68°F) or more

    2. Engine coolant temperature sensor malfunction is not detected

    3. Time after NSW input signal on to off is 2 seconds or more

  2. All of the following conditions (a), (b) and (c) are met


    1. Engine coolant temperature is less than 20°C (68°F)

    2. Engine coolant temperature sensor malfunction is detected

    3. Time after NSW input signal on to off is 30 seconds or more

(B) While vehicle is being driven, no vehicle speed sensor signal is sent to ECM

  • Open or short in speed signal circuit

  • Combination meter assembly

  • Skid control ECU

  • Main body ECU

  • Audio/visual system

  • Windshield wiper relay

  • Headlight leveling ECU

  • Navigation Receiver assembly

  • ECM

WIRING DIAGRAM

A01CC9KE03

INSPECTION PROCEDURE

Tech Tips

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)


    1. Drive the vehicle and check whether the operation of the speedometer in the combination meter assembly is normal.

      Tech Tips


      • The vehicle speed sensor is operating normally if the speedometer reading is normal.

      • If the speedometer does not operate, check it by following the procedure described for a speedometer malfunction.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the engine switch on (IG).

    4. Turn the tester on.

    5. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Vehicle Speed.

    6. Drive the vehicle.

    7. Read the value displayed on the tester.

      OK
      Vehicle speeds displayed on the tester and speedometer display are equal.

    NG

    CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM) Click here

    OK

    CHECK FOR INTERMITTENT PROBLEMS Click here

  2. CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)


    1. A01CEU2E40
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to Combination Meter Assembly)
      *2 Turn Wheel

      Inspect the combination meter assembly using an oscilloscope.


      1. Jack up the vehicle.

      2. Turn the engine switch on (IG).

      3. Move the shift lever to N.

      4. Measure the voltage between the terminal of the combination meter assembly and the body ground while the wheel is turned slowly.

        Standard Voltage
        Tester Connection Switch Condition Specified Condition
        G19-24 (+S) - Body ground Engine switch on (IG) Voltage generated intermittently

        Tech Tips

        The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.


    NG

    GO TO METER / GAUGE SYSTEM (SPEED SIGNAL CIRCUIT) Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)


    1. Disconnect the combination meter assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      G19-24 (+S) - A8-8 (SPD) Always Below 1 Ω

    4. Reconnect the combination meter assembly connector.

    5. Reconnect the ECM connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

    OK

    REPLACE ECM Click here