ROOF HEADLINING (for 5 Door) INSTALLATION

CAUTION:

Some of these service operations affect the SRS airbag system. Be sure to read the precautionary notices concerning the SRS airbag system before servicing (w/ front seat side airbag and curtain shield airbag) Click here.


  1. INSTALL ROOF HEADLINING

    A01382EE01

    1. Gently remove the backing sheet and any adhesive remaining on the roof panel.

      Tech Tips

      It is not necessary to remove the adhesive completely.

    2. Apply adhesive (Henkel Terostat 8595N/MT) to a new roof headlining.

      Specification
      Area Measurement
      A φ6 to 8 mm (0.236 to 0.315 in.)
      B 290 mm (11.417 in.)
      C 395 mm (15.551 in.)
      D 20 to 30 mm (0.787 to 1.181 in.)

      Note


      • Apply adhesive 20 to 30 mm (0.787 to 1.181 in.) away from the markings placed on the roof headlining.

      • Avoid adhesive accumulation.

    3. A0137AX

      Install the roof headlining onto the vehicle.

    4. A0136UGE01

      Push the roof headlining up to the roof panel until the distance between the roof panel and the backing sheet is less than 4 mm (0.157 in.) at all 18 points shown in the illustration.

      Specification
      Area Measurement
      A 430 mm (16.929 in.)
      B 145 mm (5.709 in.)
      C 335 mm (13.189 in.)
      D 280 mm (11.024 in.)
      E 197 mm (7.756 in.)
      F 20 mm (0.787 in.)
      G 4 mm or less (0.157 in. or less)
      H 10 mm or less (0.394 in. or less)

      Note


      • Be sure to press the roof headlining onto the roof panel with clean hands.

      • Gently and uniformly press the whole roof headlining since pressing it locally could damage it.

    5. Insert a clean needle into the 18 points shown in the illustration from the roof headlining side, and press the roof headlining until the distance between the roof panel and roof headlining surface is less than 10 mm (0.394 in.).

      Note

      Do not stick the needle into areas where adhesive is applied, as this could make the roof headlining dirty.

    6. A0136S2

      Engage the 2 hooks

    7. Install the 2 clips.

  2. INSTALL ROOM LIGHT ASSEMBLY

    A01375IE01

    1. Connect the room light connector.

    2. Engage the 2 claws and install the room light.

  3. INSTALL VISOR HOLDER

    A0136PU

    Tech Tips

    Use the same procedure as for the opposite side.


    1. Engage the claw and install the visor holder.

    2. Tighten the screw.

  4. INSTALL VISOR ASSEMBLY RH

    A0136SJ

    1. Install the visor with the 2 screws.

    2. Install the visor into the visor holder.

  5. INSTALL VISOR ASSEMBLY LH

    Tech Tips

    Use the same procedure as for the RH side.

  6. INSTALL CENTER PILLAR GARNISH UPPER RH

    A0138AK

    1. Pass the front seat outer belt through the slit of the center pillar garnish.

    2. Engage the clip and claw, and install the center pillar garnish.

  7. INSTALL CENTER PILLAR GARNISH UPPER LH

    Tech Tips

    Use the same procedure as for the RH side.

  8. INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH

    A0138E5

    1. Install the lap outer anchor plate of the front seat outer belt with the bolt.

      Torque:
      42 N*m  { 430 kgf*cm, 31 ft.*lbf }

  9. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

    Tech Tips

    Use the same procedure as for the RH side.

  10. INSTALL CENTER PILLAR GARNISH LOWER RH

    A0137HU

    1. Engage the 2 clips and 3 claws, and install the center pillar garnish.

  11. INSTALL CENTER PILLAR GARNISH LOWER LH

    Tech Tips

    Use the same procedure as for the RH side.

  12. INSTALL ROOF SIDE GARNISH INNER RH

    A013735

    1. Pass the rear seat outer belt through the slit of the roof side garnish.

    2. Engage the 3 clips and claw, and install the roof side inner garnish.

    3. Tighten the screw.

    4. Install the clip.

  13. INSTALL ROOF SIDE GARNISH INNER LH

    Tech Tips

    Use the same procedure as for the RH side.

  14. INSTALL REAR SEAT SIDE GARNISH RH

    A0136F9

    1. Engage the clip and 6 claws, and install the rear seat side garnish.

    2. Install the clip.

  15. INSTALL REAR SEAT SIDE GARNISH LH

    Tech Tips

    Use the same procedure as for the RH side.

  16. INSTALL REAR SEAT OUTER BELT ASSEMBLY RH

    A0136AS

    1. Install the lap outer anchor plate of the rear seat outer belt with the bolt.

      Torque:
      42 N*m  { 430 kgf*cm, 31 ft.*lbf }

  17. INSTALL REAR SEAT OUTER BELT ASSEMBLY LH

    Tech Tips

    Use the same procedure as for the RH side.

  18. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY

    A01366X

    1. Install the package tray trim panel.

  19. INSTALL FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)

    A0138GXE01

    1. Remove the adhesive tape and protective cover.

    2. A0138EWE01

      Install a new clip.

    3. Engage the 2 claws and 2 clips, and install the front pillar garnish.

  20. INSTALL FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

    Tech Tips

    Use the same procedure as for the RH side.

  21. INSTALL FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)

    A01391L

    1. Engage the 2 claws and 2 clips, and install the front pillar garnish.

  22. INSTALL FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

    Tech Tips

    Use the same procedure as for the RH side.

  23. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

    A0137N9

    1. Install the rear door opening trim weatherstrip.

  24. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

    Tech Tips

    Use the same procedure as for the RH side.

  25. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    A01377Z

    1. Install the front door opening trim weatherstrip.

  26. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    Tech Tips

    Use the same procedure as for the RH side.

  27. INSTALL COWL SIDE TRIM BOARD RH

    A0138HI

    1. Engage the 2 clips and stud bolt, and install the cowl side tirm board.

  28. INSTALL COWL SIDE TRIM BOARD LH

    Tech Tips

    Use the same procedure as for the RH side.

  29. INSTALL REAR SEAT BACK ASSEMBLY (for Separate Seat Type)

    A0136X9E01

    1. Place the rear seat back in the cabin.

    2. Using several steps, install and tighten the 4 nuts, 4 bolts and 2 rear seat inner belts uniformly in the sequence shown in the illustration.

      Torque:
      22 N*m  { 225 kgf*cm, 16 ft.*lbf, for 1, 2, 3 and 4 }
      33.8 N*m  { 345 kgf*cm, 25 ft.*lbf, for 5 and 6 }
      42 N*m  { 430 kgf*cm, 31 ft.*lbf, for 7 and 8 }

    3. Lock the 2 hooks.

  30. INSTALL REAR SEAT BACK ASSEMBLY (for Bench Seat Type)

    A0136F8E01

    1. Place the rear seat back in the cabin.

    2. Using several steps, install and tighten the 2 nuts and 2 bolts uniformly in the sequence shown in the illustration.

      Torque:
      22 N*m  { 225 kgf*cm, 16 ft.*lbf }

    3. Engage the 2 hooks.

  31. INSTALL REAR SEAT CUSHION ASSEMBLY (for Separate Seat Type)

    A0137NL

    1. Engage the 4 hooks and install the rear seat cushion.

  32. INSTALL REAR SEAT CUSHION ASSEMBLY (for Bench Seat Type)

    A01392V

    1. Engage the 4 hooks and install the rear seat cushion.

  33. INSTALL FRONT SEAT ASSEMBLY LH

    A01384RE01

    1. Place the front seat in the cabin.

    2. Using several steps, install and tighten the 4 bolts uniformly in the sequence shown in the illustration.

      Torque:
      22 N*m  { 225 kgf*cm, 16 ft.*lbf }
    3. A013693

      Connect the airbag connector, as shown in the illustration (w/ front seat side airbag).

    4. Connect the buckle switch connector (driver seat only).

    5. Install the wire harness clamp.

  34. INSTALL FRONT SEAT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  35. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Torque:
    5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

  36. INSPECT SRS WARNING LIGHT (w/ Front Seat Side Airbag and Curtain Shield Airbag)

    Click here