FRONT SEAT ASSEMBLY INSTALLATION

INSTALL PARKING BRAKE LEVER SUB-ASSEMBLY

1. Install the parking brake lever with the 2 bolts.

   Torque:

   14.5 N*m  { 148 kgf*cm, 11 ft.*lbf }

2. 

   Connect the parking brake switch connector.

INSTALL PARKING BRAKE EQUALIZER

1. Install the equalizer with a new adjusting nut.

INSPECT PARKING BRAKE LEVER TRAVEL

1. Slowly pull the parking brake lever to the fully applied position, counting the number of clicks.

   Parking brake lever travel
   5 to 8 clicks at 196 N (20 kgf, 44 lbf)

ADJUST PARKING BRAKE LEVER TRAVEL

1. Turn the adjusting nut until the parking brake lever travel is corrected to within the specified range.

   Parking brake lever travel
   5 to 8 clicks at 196 N (20 kgf, 44 lbf)

2. Operate the parking brake lever 3 to 4 times, and check the parking brake lever travel.

3. Check whether the parking brake drags or not.

4. When operating the parking brake lever, check that the brake warning light comes on.

   Standard
   Brake warning light always comes on at the first notch.

INSTALL CONSOLE BOX SUB-ASSEMBLY REAR

1. Install the console box with the 2 bolts.

INSTALL REAR SEAT SIDE GARNISH RH (for 5 Door)

1. Pass the rear seat outer belt through the slit of the roof side garnish inner.

2. Engage the 3 clips and claw, and install the roof side garnish inner.

3. Tighten the screw.

4. Install the clip.

INSTALL QUARTER INSIDE TRIM BOARD RH (for 3 Door)

1. Engage the 7 claws and 7 clips, and install quarter inside trim board.

2. Install the clip.

INSTALL REAR SEAT OUTER BELT ASSEMBLY RH (for 5 Door)

1. Install the lap outer anchor plate of the rear seat outer belt with the bolt.

   Torque:

   42 N*m  { 430 kgf*cm, 31 ft.*lbf }

INSTALL REAR SEAT OUTER BELT ASSEMBLY RH (for 3 Door)

1. Install the lap outer anchor plate of the rear seat outer belt with the bolt.

   Torque:

   42 N*m  { 430 kgf*cm, 31 ft.*lbf }

INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH (for 5 Door)

1. Install the lap outer anchor plate of the front seat outer belt with the bolt.

   Torque:

   42 N*m  { 430 kgf*cm, 31 ft.*lbf }

INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH (for 3 Door)

1. Install the lap outer anchor plate of the front seat outer belt with the bolt.

   Torque:

   42 N*m  { 430 kgf*cm, 31 ft.*lbf }

INSTALL REAR SEAT BACK ASSEMBLY (for Separate Seat Type)

1. Place the rear seat back in the cabin.

2. Using several steps, install and tighten the 4 nuts, 4 bolts and 2 rear seat inner belts uniformly in the sequence shown in the illustration.

   Torque:

   22 N*m  { 225 kgf*cm, 16 ft.*lbf, for 1, 2, 3 and 4 }

   33.8 N*m  { 345 kgf*cm, 25 ft.*lbf, for 5 and 6 }

   42 N*m  { 430 kgf*cm, 31 ft.*lbf, for 7 and 8 }

3. Lock the 2 hooks.

INSTALL REAR SEAT BACK ASSEMBLY (for Bench Seat Type)

1. Place the rear seat back in the cabin.

2. Using several steps, install and tighten the 2 nuts and 2 bolts uniformly in the sequence shown in the illustration.

   Torque:

   22 N*m  { 225 kgf*cm, 16 ft.*lbf }

3. Engage the 2 hooks.

INSTALL REAR SEAT CUSHION ASSEMBLY (for Separate Seat Type)

1. Engage the 4 hooks and install the rear seat cushion.

INSTALL REAR SEAT CUSHION ASSEMBLY (for Bench Seat Type)

1. Engage the 4 hooks and install the rear seat cushion.