FRONT DOOR LOCK INSTALLATION


  1. INSTALL FRONT DOOR LOCK ACTUATOR ASSEMBLY

    A0136A5

    1. Install the front door lock actuator assembly LH with the 2 screws.

  2. INSTALL FRONT DOOR LOCK ASSEMBLY


    1. Apply MP grease to the sliding and rotating components of the front door lock assembly LH.

    2. A0138CA

      Apply adhesive to the threads of the 3 screws.

      Adhesive
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    3. Using torx socket wrench T30, install the front door lock assembly with the 3 screws.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

    4. Install the bolt.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }
    5. A0137AW

      Connect the front door outside locking link, as shown in the illustration.

    6. A0138HL

      Connect the front door lock open rod, as shown in the illustration.

  3. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

    A0138ZME01

    1. Disengage claw A.

    2. Move the front door inside handle sub-assembly in the direction indicated by the arrow mark in the illustration. This will release the claws and allow the removal of the front door inside handle sub-assembly.

    3. A0137TX

      Disconnect the cable from the front door inside handle sub-assembly by pulling it in the direction indicated by the arrow in the illustration.

  4. INSTALL FRONT DOOR FRAME SUB-ASSEMBLY REAR LOWER

    A0137QE

    1. Install the bolt and front door frame sub-assembly rear lower.

      Torque:
      6.1 N*m  { 62 kgf*cm, 54 in.*lbf }

  5. INSTALL FRONT DOOR FRAME SUB-ASSEMBLY FRONT LOWER

    A0136H6

    1. Install the bolt and front door frame sub-assembly front lower.

      Torque:
      6.1 N*m  { 62 kgf*cm, 54 in.*lbf }

  6. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY

    A01360T

    1. Install the front door window regulator sub-assembly with the 3 nuts.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

      Note

      Do not drop the front door window regulator sub-assembly as it may be damaged.

    2. Connect the connector.

  7. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

    A01382R

    1. Install the front door glass sub-assembly onto the window regulator with the 2 screws.

      Torque:
      2.8 N*m  { 29 kgf*cm, 25 in.*lbf }

  8. INSTALL FRONT DOOR GLASS RUN

    A0138IL

    1. Install the front door glass run.

  9. INSTALL FRONT DOOR GLASS WEATHERSTRIP ASSEMBLY INNER

  10. INSTALL FRONT DOOR GLASS WEATHERSTRIP ASSEMBLY OUTER

    A01365KE01

    1. Engage the 5 claws and install the front door belt moulding.

    2. Remove the protective tape.

  11. INSTALL FRONT DOOR SERVICE HOLE COVER

    A0138PI

    1. Apply butyl tape to the door.

    2. Install a new front door service hole cover.

      Tech Tips

      Remove all wrinkles or folds when attaching the front door service hole cover.

  12. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY

    A0138TB

    1. Install the outer rear view mirror assembly LH with the 3 screws.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

      Note


      • Do not tighten the screws to more than the specified torque.

      • Before tightening the screws to the specified torque, provisionally tighten the screws by hand to fit the threads. Do not remove and reinstall the screws more than twice, when reusing a mirror.

  13. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

    A0137G6E02

    1. Engage the 2 clips and install the 2 screws.

  14. INSTALL FRONT DOOR FRONT LOWER FRAME COVER UPPER

    A0136I0

    1. Install the front door front lower frame cover upper by sliding it in the direction indicated by the arrow.

  15. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

    A0136RFE01

    1. Engage the 15 clips and install the front door trim board sub-assembly.

    2. Install the screw.

  16. INSTALL FRONT ARMREST BASE PANEL UPPER

    A013832

    1. Connect the connector.

    2. A013827E01

      Engage the 3 claws and install the front armrest base panel upper.

  17. INSTALL ASSIST GRIP ASSEMBLY

    A0137X5E01

    1. Engage the 4 claws and install the 2 screws.

  18. INSTALL DOOR ASSIST GRIP COVER

    A0137O5E01

    1. Engage the 2 claws and install the door assist grip cover.

  19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Torque:
    5.4 N*m  { 55 kgf*cm, 48 in.*lbf }