HEADLIGHT DIMMER SWITCH INSTALLATION


  1. INSTALL HEADLIGHT DIMMER SWITCH ASSEMBLY

    A0137OUE01

    1. Engage the 2 claws and install the headlight dimmer switch assembly, as shown in the illustration.

    2. A0138EYE01

      Install the headlight dimmer switch assembly with the clamp.

    3. Connect the connector.

  2. INSTALL COMBINATION METER ASSEMBLY

    A0137AB

    1. Connect the 14 connectors.

    2. Install the combination meter with the 2 bolts.

      Torque:
      6.5 N*m  { 66 kgf*cm, 58 in.*lbf }

  3. INSTALL SPIRAL CABLE SUB-ASSEMBLY

    A01383L

    1. Check that the front wheels are facing straight ahead.

    2. Set the turn signal switch in the neutral position.

      Note

      Make sure that the turn signal switch is in the neutral position or the pin of the turn signal switch may be snapped.

    3. Engage the 3 claws and install the spiral cable.

      Note

      When replacing the spiral cable with a new one, remove the lock pin before installing the steering wheel.

    4. Connect the steering angle sensor connector (w/ VSC).

    5. Connect the airbag connector, as shown in the illustration.

      Note

      When handling the airbag connector, do not damage the airbag wire harness.

    6. Connect the horn connector.

  4. CENTER SPIRAL CABLE

  5. INSTALL STEERING WHEEL ASSEMBLY


    1. Align the matchmarks on the steering wheel assembly and the steering main shaft assembly.

    2. Install the steering wheel assembly set nut.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

  6. INSTALL STEERING PAD

    A0136JY

    1. Support the steering pad with one hand, as shown in the illustration.

    2. Connect the airbag connector, as shown in the illustration.

      Note

      When handling the airbag connector, do not damage the airbag wire harness.

    3. Connect the horn connector.

    4. A0138S9E01

      Confirm that the circumference groove of the screw fits into the screw case, and place the steering pad onto the steering wheel.

    5. Using "Torx" socket wrench T30, tighten the 2 screws.

      Torque:
      8.8 N*m  { 90 kgf*cm, 78 in.*lbf }

  7. INSTALL WINDSHIELD WIPER SWITCH ASSEMBLY

    A0138JZE01

    1. Engage the claw and install the windshield wiper switch assembly.

    2. Connect the 2 connectors.

  8. INSTALL STEERING COLUMN COVER UPPER

    A0136TV

    1. Install the steering column cover upper, as shown in the illustration (w/ tachometer).

    2. A0136OJE02

      While turning the steering wheel to the right and left, engage the 4 claws and install the steering column cover upper with the 2 screws.

      Torque:
      2.0 N*m  { 20 kgf*cm, 18 in.*lbf }
    3. A0137VI

      Tighten the screw behind the tachometer (w/ tachometer).

      Note

      Tighten the screw if the tachometer has been extended and the column cover has been removed.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

  9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Torque:
    5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

  10. INSPECT HORN BUTTON ASSEMBLY

    A0137L5

    1. With the steering pad on the vehicle, perform a visual check including the following.


      1. Any cuts, minute cracks or marked discoloration on the steering pad top surface or in the grooved portion.

    2. Make sure that the horn sounds.

      If the horn does not sound, check the horn system Click here.

  11. INSPECT SRS WARNING LIGHT

    Click here