DAYTIME RUNNING LIGHT ASSEMBLY INSTALLATION


  1. INSTALL DAYTIME RUNNING LIGHT ASSEMBLY


    1. Connect the connector and temporarily install the daytime running light assembly to the daytime running light bracket.

    2. A0137X8

      Slide the daytime running light in the direction shown in the illustration to engage the 2 guides.

    3. Install the screw.

    4. Install the daytime running light bracket with the 3 screws.

    5. Engage the 2 clamps.

  2. INSTALL FRONT BUMPER COVER


    1. Install the 2 clips.

    2. Connect the connectors.

      Tech Tips

      If the vehicle is equipped with fog light and daytime running lights, connect the connectors.

    3. Engage the 10 claws and install the front bumper cover.

    4. A0136VM

      Tighten the 3 bolts and 5 screws.

    5. Install the 3 clips.

    6. Remove the protective tape.

  3. INSTALL FRONT SPOILER (w/ Front Spoiler)

    Click here

  4. PREPARE VEHICLE FOR FOG LIGHT AIMING ADJUSTMENT (w/ Fog Light)


    1. Prepare the vehicle:


      • Ensure that there is no damage or deformation of the body around the fog lights.

      • Fill the fuel tank.

      • Fill the oil to the specified level.

      • Fill the coolant to the specified level.

      • Inflate the tires to the appropriate pressure.

      • Place the spare tire, tools and jack in their original positions.

      • Unload the trunk.

      • Sit a person of average weight (75 kg, 165 lb) in the driver seat.

  5. PREPARE FOR FOG LIGHT AIMING (w/ Fog Light)


    1. A0137GWE03

      Prepare the vehicle in accordance with the following conditions:


      • Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the fog lights can be observed and above which it cannot.

      • Place the vehicle at a 90° angle to the wall.

      • Keep a 25 m (82 ft.) distance between the center of the fog light bulb and the wall.

      • Place the vehicle on a level surface.

      • Bounce the vehicle up and down to settle the suspension.

      Tech Tips

      A distance of 25 m (82 ft.) between the vehicle (center of the fog light bulb) and the wall is necessary for proper aim adjustment. If unable to secure a distance of 25 m (82 ft.), secure a distance of exactly 3 m (9.84 ft.) to check and adjust the fog light aim (Since the target zone will change with the distance, follow the instructions shown in the illustration.).

    2. Prepare a piece of thick white paper (approximately 2 m (6.6 ft.) (high) x 4 m (13.1 ft.) (wide)), to use as a screen.

    3. Draw a vertical line down the center of the screen (V line).

    4. Set the screen as shown in the illustration.

      Tech Tips


      • Stand the screen perpendicular to the ground.

      • Align the V line on the screen with the center of the vehicle.

      A013919E03
    5. A01375SE24
      Text in Illustration
      *a V LH Line
      *b V Line
      *c V RH Line
      *d H Line
      *e Ground

      Draw base lines (H line, V LH, V RH lines) on the screen as shown in the illustration.

      Tech Tips

      Mark the fog light bulb center marks on the screen. If the center mark cannot be observed on the fog light, use the center of the fog light bulb or the manufacturer's name marked on the fog light as the center mark.


      1. H Line (Fog light height):

        Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the fog light bulb center marks of the fog lights.

      2. V LH Line and V RH Line (Center mark positions of left-hand (LH) and right-hand (RH) fog lights):

        Draw 2 vertical lines so that they intersect the H line at each center mark.

  6. INSPECT FOG LIGHT AIMING (w/ Fog Light)


    1. Cover the fog light or disconnect the connector of the fog light on the opposite side to prevent light from the fog light not being inspected from affecting fog light aiming inspection.

      Note

      Do not keep the fog light covered for more than 3 minutes. The fog light is made with plastic components, which may melt or be damaged due to excessive heat.

    2. Start the engine.

      Tech Tips

      Engine speed must be 1500 rpm or more.

    3. Turn on the fog light and make sure that the cutoff line falls within the specified area, as shown in the illustration.

      A0136M5E58

      Tech Tips


      • If the alignment distance is 25 m (82 ft.): The upper edge of the hot zone for the fog light should be 433 mm (17.06 in.) below the H line.

      • If the alignment distance is 3 m (9.84 ft.): The upper edge of the hot zone for the fog light should be 52 mm (2.04 in.) below the H line.

  7. ADJUST FOG LIGHT AIMING (w/ Fog Light)


    1. A0137AF

      Adjust the fog light aim to within the specified range by turning the aiming screw with a screwdriver.

      Note

      The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.