CURTAIN SHIELD AIRBAG ASSEMBLY (for 5 Door) DISPOSAL

Tech Tips


  • Disposal procedure for the RH side is the same as that for the LH side.

  • The procedures listed below are for the RH side.

  • When scrapping a vehicle equipped with the SRS or disposing of a curtain shield airbag, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the SERVICE DEPT. of the DISTRIBUTOR.

CAUTION:


  • Never dispose of a curtain shield airbag that is undeployed.

  • The airbag emits an exploding sound when it is deployed, so perform the operation outdoors and where it will not create a nuisance to nearby residents.

  • A0136FIE01

    When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool). Perform the operation in a place away from electrical noise.

  • When deploying the airbag, perform the operation at least 10 m (33 ft) away from the curtain shield airbag.

  • The curtain shield airbag becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

  • Use gloves and safety glasses when handling a curtain shield airbag which has been deployed.

  • Do not apply water, etc. to a curtain shield airbag which has been deployed.

  • Always wash your hands with water after completing the operation.


  1. DISPOSE OF CURTAIN SHIELD AIRBAG ASSEMBLY (When Installed in Vehicle)

    Tech Tips

    Prepare a battery as the power source to deploy the airbag.


    1. A0136FIE01

      Check the function of SST.

      SST
      09082-00700

      CAUTION:

      When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool).


      1. A0138OVE12
        Text in Illustration
        *1 Battery

        Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.

      2. A0136WJE01

        Press the SST activation switch, and check that the LED of the SST activation switch comes on.

        CAUTION:


        • Do not connect the SST connector (yellow colored one) to the airbag.

        • If the LED comes on when the activation switch is not pressed, SST malfunction is possible, so be sure not to use SST.

      3. Disconnect SST from the battery.

    2. Disconnect the cable from the negative battery terminal.

    3. Remove the roof headlining Click here.

    4. A0135TG

      Disconnect the airbag connector, as shown in the illustration.

      Note

      When handling the airbag connector, do not damage the airbag wire harness.

    5. A01384KE01

      Connect SST.

      SST
      09082-00700
      09082-00802   ( 09082-10801, 09082-20801 )

      1. After connecting SST, connect it to the curtain shield airbag.

        Note

        To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the twin lock.

      2. A0138WXE02
        Text in Illustration
        *1 Battery
        *a 10 m (33 ft) or more

        Move SST to at least 10 m (33 ft) away from the vehicle.

      3. Close all doors and windows of the vehicle.

        Note

        Do not damage the SST wire harness.

      4. Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.

    6. Deploy the airbag.


      1. Check that no one is inside the vehicle or within a 10 m (33 ft) radius of the vehicle.

      2. Press the SST activation switch and deploy the airbag.

        CAUTION:


        • When deploying the airbag, make sure that no one is near the vehicle.

        • The curtain shield airbag becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

        • Use gloves and safety glasses when handling a curtain shield airbag which has been deployed.

        • Do not apply water, etc. to a curtain shield airbag which has been deployed.

        • Always wash your hands with water after completing the operation.

        Tech Tips

        The airbag is deployed as the LED of the SST activation switch comes on.

  2. DISPOSE OF CURTAIN SHIELD AIRBAG ASSEMBLY (When not Installed in Vehicle)

    Note


    • When disposing of a curtain shield airbag, never use the customer's vehicle to deploy the airbag.

    • Be sure to follow the procedure detailed below when deploying the airbag.

    Tech Tips

    Prepare a battery as the power source to deploy the airbag.


    1. A0136FIE01

      Check the function of SST.

      SST
      09082-00700

      CAUTION:

      When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool).


      1. A0138OVE12
        Text in Illustration
        *1 Battery

        Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.

      2. A0136WJE01

        Press the SST activation switch, and check that the LED of the SST activation switch comes on.

        CAUTION:


        • Do not connect the SST connector (yellow colored one) to the airbag.

        • If the LED comes on when the activation switch is not pressed, SST malfunction is possible, so be sure not to use SST.

      3. Disconnect SST from the battery.

    2. Remove the curtain shield airbag Click here.

    3. A0137GV

      Remove the clamp from the curtain shield airbag.

    4. A01375ZE02
      Text in Illustration
      *a Cut

      Cut off the deployment section of the curtain shield airbag.

    5. A0136L7E01

      Connect SST.

      SST
      09082-00802   ( 09082-10801, 09082-20801 )

      1. After connecting SST, connect it to the curtain shield airbag.

        Note

        To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the twin lock.

    6. A01371LE47

      Using a service-purpose wire harness for the vehicle, tie the curtain shield airbag to the tire.

      Text in Illustration
      *a Stripped Wire Harness Section
      Stripped wire harness section:
      Area Measurement
      A

      1.25 mm2or more (0.0019 in.2or more)

      CAUTION:

      If the wire harness is too thin or any other object is used to tie the curtain shield airbag, it may be snapped by the shock when the airbag is deployed. Always use a wire harness for vehicle use with a cross sectionof at least 1.25 mm2(0.0019 in2).

      Tech Tips

      To calculate the area of the stripped wire harness cross section:

      Area = 3.14 x (Diameter)2divided by 4


      1. A01387AE01

        Position the curtain shield airbag inside the tire, as shown in the illustration.

        Tire size:
        Area Measurement
        A 185 mm (7.28 in.)
        B 360 mm (14.17 in.)

        CAUTION:

        Make sure that the wire harnesses are tight. If there is any slack in the wire harness, the curtain shield airbag may become loose due to the shock when the airbag is deployed.

        Note

        The tire will be marked by the airbag deployment, so use a waste tire.

    7. A0136K1E02
      Text in Illustration
      *1 Tire (2 or more)

      Place the tires.

      CAUTION:

      Do not place the curtain shield airbag with the deployment direction facing toward the ground.


      1. Place at least 2 tires under the tire to which the curtain shield airbag is tied.

      2. Place at least 2 tires over the tire to which the curtain shield airbag is tied. The disc wheel should be installed onto the top tire.

        Note

        Do not place the SST connector under the tire because it could be damaged.

      3. A0136OIE04
        Text in Illustration
        *1 Wire Harness

        Tie the tires together with 2 wire harnesses.

        CAUTION:

        Make sure that the wire harnesses are tight. It is highly dangerous when a loose wire harness results in the tires coming free due to the shock when the airbag is deployed.

    8. A0137YDE02
      Text in Illustration
      *1 Battery
      *a 10 m (33 ft) or more

      Connect SST.

      SST
      09082-00700

      Note

      To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the tire.

    9. Deploy the airbag.


      1. Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.

      2. Check that no one is within a 10 m (33 ft) radius of the tire to which the curtain shield airbag is tied.

      3. Press the SST activation switch and deploy the airbag.

        CAUTION:

        When deploying the airbag, make sure that no one is near the tire.

        Tech Tips

        The airbag is deployed as the LED of the SST activation switch comes on.

    10. A0137Y2E02
      Text in Illustration
      *1 Plastic Bag

      Dispose of the curtain shield airbag.

      CAUTION:


      • The curtain shield airbag becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

      • Use gloves and safety glasses when handling a curtain shield airbag which has been deployed.

      • Always wash your hands with water after completing the operation.

      • Do not apply water, etc. to a curtain shield airbag which has been deployed.


      1. Remove the curtain shield airbag from the tire.

      2. Place the curtain shield airbag in a plastic bag, tie it tightly and dispose of it in the same way as other general parts.