SIDE AIRBAG SENSOR (for 5 Door) INSTALLATION

CAUTION:

Some of these service operations affect the SRS airbag system. Be sure to read the precautionary notices concerning the SRS airbag system before servicing Click here.

Tech Tips


  • Use the same procedure for both the RH and LH sides.

  • The procedure listed below is for the RH side.


  1. INSTALL SIDE AIRBAG SENSOR ASSEMBLY

    A0137WW

    1. Check that the ignition switch is turned to OFF.

    2. Check that the cable is disconnected from the negative battery terminal.

      CAUTION:

      After disconnecting the cable from the negative battery terminal, wait for at least 90 seconds before starting the operation.

    3. Connect the airbag connector, as shown in the illustration.

    4. A01385N

      Install the side airbag sensor with the nut.

      Torque:
      9.0 N*m  { 90 kgf*cm, 80 in.*lbf }

  2. INSTALL FRONT SEAT OUTER BELT ASSEMBLY

    A0138KXE01

    1. Check the angle of inclination required to lock the retractor.


      1. Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15° or less in any direction. Also, check that the belt locks when the inclination of the retractor is 45° or more.

        Note

        Do not disassemble the retractor.

        If the operation is not as specified, replace the front seat outer belt.

    2. A013634E01

      Hook the lower stay of the retractor onto the 2 body hooks.

    3. Tighten bolt A, and then tighten bolt B.

      Torque:
      4.9 N*m  { 50 kgf*cm, 43 in.*lbf, for bolt A }
      42 N*m  { 430 kgf*cm, 31 ft.*lbf, for bolt B }
    4. A0136M8

      Install the through anchor with the bolt.

      Torque:
      42 N*m  { 430 kgf*cm, 31 ft.*lbf }

    5. Check that the through anchor rotates smoothly.

    6. A0138E5

      Install the lap outer anchor plate with the bolt.

      Torque:
      42 N*m  { 430 kgf*cm, 31 ft.*lbf }

    7. Check that the ELR locks.

      Note


      • The check should be performed with the front seat outer belt installed.

      • Do not allow the anchor part of the front seat outer belt and the protruding parts of the floor panel to overlap.


      1. With the belt installed, check that the belt locks when it is pulled out quickly.

        If the operation is not as specified, replace the front seat outer belt.

    8. Remove the bolt and lap outer anchor plate.

    9. A0136WW

      Connect the pretensioner connector, as shown in the illustration.

  3. INSTALL CENTER PILLAR GARNISH UPPER

    A0138AK

    1. Engage the clip and claw, and install the center pillar garnish.

    2. A0138E5

      Install the lap outer anchor plate of the front seat outer belt with the bolt.

      Torque:
      42 N*m  { 430 kgf*cm, 31 ft.*lbf }

  4. INSTALL CENTER PILLAR GARNISH LOWER

    A0137HU

    1. Engage the 2 clips and 3 claws, and install the center pillar garnish.

  5. INSTALL REAR SEAT SIDE GARNISH

    A0136F9

    1. Engage the clip and 6 claws, and install the rear seat side garnish.

    2. Install the clip.

  6. INSTALL REAR SEAT OUTER BELT ASSEMBLY

    A0136AS

    1. Install the lap outer anchor plate of the rear seat outer belt with the bolt.

      Torque:
      42 N*m  { 430 kgf*cm, 31 ft.*lbf }

  7. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP

    A0137N9

    1. Install the rear door opening trim weatherstrip.

  8. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP

    A01387H

    1. Install the front door opening trim weatherstrip.

  9. INSTALL REAR SEAT BACK ASSEMBLY (for Separate Seat Type)

    A0136X9E01

    1. Place the rear seat back in the cabin.

    2. Using several steps, install and tighten the 4 nuts, 4 bolts and 2 rear seat inner belts uniformly in the sequence shown in the illustration.

      Torque:
      22 N*m  { 225 kgf*cm, 16 ft.*lbf, for 1, 2, 3 and 4 }
      33.8 N*m  { 345 kgf*cm, 25 ft.*lbf, for 5 and 6 }
      42 N*m  { 430 kgf*cm, 31 ft.*lbf, for 7 and 8 }

    3. Lock the 2 hooks.

  10. INSTALL REAR SEAT BACK ASSEMBLY (for Bench Seat Type)

    A0136F8E01

    1. Place the rear seat back in the cabin.

    2. Using several steps, install and tighten the 2 nuts and 2 bolts uniformly in the sequence shown in the illustration.

      Torque:
      22 N*m  { 225 kgf*cm, 16 ft.*lbf }

    3. Engage the 2 hooks.

  11. INSTALL REAR SEAT CUSHION ASSEMBLY (for Separate Seat Type)

    A0137NL

    1. Engage the 4 hooks and install the rear seat cushion.

  12. INSTALL REAR SEAT CUSHION ASSEMBLY (for Bench Seat Type)

    A01392V

    1. Engage the 4 hooks and install the rear seat cushion.

  13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Torque:
    5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

  14. INSPECT SRS WARNING LIGHT

    Click here