AIRBAG SYSTEM SRS Warning Light does not Come ON

DESCRIPTION

The SRS warning light is located on the combination meter.

When the SRS (Supplemental Restraint System) is functioning normally, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from the LOCK position to the ON position, and then turns off automatically.

If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver.

When the SRS warning light does not come on even after turning the ignition switch to ON, perform the inspection in accordance with the following procedures.

WIRING DIAGRAM

A0136GSE01
A013642E01

INSPECTION PROCEDURE

Note

In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.


  1. Turn the ignition switch to the LOCK position.

  2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  3. Disconnect the connectors from the center airbag sensor assembly.

  4. Disconnect the connectors from the steering pad.

  5. Disconnect the connector from the front passenger airbag assembly.

  6. Disconnect the connector from the front seat outer belt assembly LH.

  7. Disconnect the connector from the front seat outer belt assembly RH.

    Tech Tips

    Skip the following steps if side and curtain shield airbags are not fitted.

  8. Disconnect the connector from the front seat airbag assembly LH.

  9. Disconnect the connector from the front seat airbag assembly RH.

  10. Disconnect the connector from the curtain shield airbag assembly LH.

  11. Disconnect the connector from the curtain shield airbag assembly RH.

PROCEDURE


  1. CHECK BATTERY


    1. Measure the battery voltage.

      Standard Voltage
      11 to 14 V

    NG

    REPAIR OR REPLACE BATTERY

    OK

  2. CHECK CONNECTION OF CONNECTOR


    1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    2. Check that the connectors are properly connected to the center airbag sensor assembly and combination meter.

      OK
      The connectors are properly connected.

    NG

    CONNECT CONNECTOR

    OK

  3. CHECK CONNECTOR


    1. Check that the connectors (on the center airbag sensor assembly side and combination meter side) are not damaged Click here.

      OK
      The connectors are not deformed or damaged.

    NG

    REPAIR OR REPLACE INSTRUMENT PANEL WIRE

    OK

  4. CHECK INSTRUMENT PANEL WIRE (AIRBAG SENSOR ASSEMBLY CENTER - COMBINATION METER ASSEMBLY)


    1. A0137ZJE01

      Disconnect the connectors from the center airbag sensor assembly and combination meter.

    2. Measure the resistance.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C19-19 (LA) - C1-19 (SW) Always Below 1 Ω
      C19-19 (LA) - Body ground Always 1 MΩ or Higher

    3. Connect the negative (-) terminal cable to the battery.

    4. Turn the ignition switch to the ON position.

    5. Measure the voltage.

      Standard Voltage
      Tester Connection Condition Specified Condition
      C1-19 (SW) - Body ground Ignition switch ON Below 1 V

    NG

    REPAIR OR REPLACE INSTRUMENT PANEL WIRE

    OK

  5. CHECK FUSE (IG2, DOME, AM2)


    1. A0136VOE03

      Remove the IG2 fuse from the driver side J/B.

    2. Remove the DOME fuse and AM2 fuse from the engine room R/B.

    3. Measure the resistance.

      Standard Resistance
      Below1 Ω

    4. Reinstall the fuses.


    NG

    INSPECT FOR SHORT CIRCUIT IN HARNESS AND ALL COMPONENTS CONNECTED TO FUSE

    OK

  6. INSPECT COMBINATION METER ASSEMBLY


    1. A0138LTE01

      Disconnect the 3G, 3H and 3K driver side J/B connectors.

    2. Measure the resistance.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3K-1 - Body ground Always Below 1 Ω

    3. Measure the voltage.

      Standard Voltage
      Tester Connection Condition Specified Condition
      3H-9 - Body ground Ignition switch ON 10 to 14 V
      3G-4 - Body ground Always 10 to 14 V

    4. Reinstall the driver side J/B connectors.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. CHECK COMBINATION METER


    1. Turn the ignition switch to the LOCK position.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Disconnect the connector from the center airbag sensor assembly.

    4. Connect the connector to the combination meter.

    5. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    6. Turn the ignition switch to the ON position.

    7. Check the SRS warning light operation.

      OK
      The SRS warning light blinks 10 seconds after the ignition switch is turned to the ON position.

    NG

    INSPECT COMBINATION METER

    OK

    REPLACE CENTER AIRBAG SENSOR ASSEMBLY