POWER STEERING ECU INSTALLATION


  1. INSTALL POWER STEERING ECU ASSEMBLY

    A01375L

    1. Install the power steering ECU assembly to the instrument panel assembly lower with the 2 bolts.

      Torque:
      1.7 N*m  { 17 kgf*cm, 15 in.*lbf }

  2. INSTALL INSTRUMENT PANEL ASSEMBLY LOWER


    1. Install the instrument panel lower with the 2 bolts <C>, 5 screws <E> or <F>, screw <D>, screw <G> and 2 clips.

      Torque:
      3.7 N*m  { 38 kgf*cm, 33 in.*lbf, for screw <G> }

    2. Connect the connectors and engage the 3 wire harness clamps.

      A013812E01

    3. Connect the antenna cord by engaging the 4 fastenings.

  3. INSTALL CONSOLE BOX (for Manual Transaxle)

    A01378K

    1. Engage the 2 claws and install the console box.

    2. Install the bolt <B>.

    3. Install the box bottom mat.

    4. Turn the shift knob in the direction indicated by the arrow in the illustration to install it.

  4. INSTALL CONSOLE BOX (for Multi-Mode Manual Transaxle)


    1. Engage the 2 claws and install the console box.

    2. Install the bolt <B>.

    3. Install the box bottom mat.

  5. INSTALL FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY (for Multi-Mode Manual Transaxle)


    1. Engage the 4 claws and install the floor shift position indicator housing sub-assembly.

    2. A0137LF

      Turn the shift knob in the direction indicated by the arrow in the illustration to install it.

  6. INSTALL HEATER CONTROL ASSEMBLY (for LHD)

    A0137HM

    Note

    Do not bend the cable when installing the heater control assembly.


    1. Insert each cable into the instrument panel.

    2. A0137SPE02
      Text in Illustration
      *1 Defroster Cable
      *2 Air Inlet Cable
      *3 Air Mix Cable

      Pass the white air inlet cable between the instrument panel and wire harness.

    3. Pass the black air mix cable between the instrument panel and wire harness.

    4. Pass the blue defroster cable between the instrument panel reinforcement and wire harness, and then outside the wire harness clamp.

    5. A0138YNE01

      Engage the 2 claws and install the heater control assembly with the 2 screws.

  7. INSTALL HEATER CONTROL ASSEMBLY (for RHD)

    A0138TT

    Note

    Do not bend the cable when installing the heater control assembly.


    1. Insert the cable into the instrument panel.

    2. A0137T7E02
      Text in Illustration
      *1 Defroster Cable
      *2 Air Inlet Cable
      *3 Air Mix Cable

      Pass the white air inlet cable through the wire harness.

    3. Pass the black air mix cable between the instrument panel and brace.

    4. Pass the blue defroster cable between the instrument panel reinforcement and wire harness, and then outside the wire harness clamp.

    5. A0138YNE01

      Engage the 2 claws and install the heater control assembly with the 2 screws.

  8. SET HEATER CONTROL BASE SUB-ASSEMBLY

    A0137FKE02
    Text in Illustration
    *a LHD
    *b RHD

    1. Make sure that the levers are placed in the position shown in the illustration.

  9. CONNECT DEFROSTER DAMPER CONTROL CABLE SUB-ASSEMBLY


    1. A01385VE02
      Text in Illustration
      *a Mode Link
      *b DEF
      *c FACE
      *d Front Side

      Turn the mode link to the DEF position.

    2. Install the cable ring onto the motor link.

    3. Hold the mode wheel knob of the heater control and install the defroster cable onto the clamp while pulling it in the direction indicated by arrow A.

      Note

      Make sure that the air mix lever knob operates correctly. Also, confirm that there is no reverse movement of the knob at either end.

  10. CONNECT AIR MIX DAMPER CONTROL CABLE SUB-ASSEMBLY


    1. A0136TQE02
      Text in Illustration
      *a Temperature Control Link
      *b COOL
      *c WARM
      *d Front Side

      Turn the temperature control link to the MAX-cool position.

    2. Install the cable ring onto the temperature control link.

    3. Hold the mode wheel knob of the heater control and install the mode cable onto the clamp while pulling it in the direction indicated by arrow A.

      Note

      Make sure that the air mix lever knob operates correctly. Also, confirm that there is no reverse movement of the knob at either end.

  11. CONNECT AIR INLET DAMPER CONTROL CABLE SUB-ASSEMBLY


    1. A01363GE02
      Text in Illustration
      *a LHD
      *b RHD
      *c Air Inlet Control Link
      *d FRESH
      *e RECIRCULATION
      *f Front Side

      Turn the air inlet control link to the RECIRCULATION position.

    2. Turn the air inlet control link to the FRESH AIR position.

    3. Install the cable ring onto the air inlet control link.

    4. Hold the air inlet lever knob of the heater control and install the air inlet cable onto the clamp while pulling it in the direction indicated by arrow A.

      Note

      Make sure that the air inlet lever knob operates correctly. Also, confirm that there is no reverse movement of the knob at either end.

  12. INSTALL COWL SIDE TRIM BOARD LH


    1. Engage the 2 clips and claw, and install the cowl side trim board LH.

  13. INSTALL COWL SIDE TRIM BOARD RH

    Tech Tips

    Perform the same procedure as for the LH.

  14. INSTALL INSTRUMENT PANEL ASSEMBLY

    Click here