MULTI-MODE MANUAL TRANSAXLE ECU INSTALLATION

INSTALL INSTRUMENT PANEL SUB-ASSEMBLY LOWER

1. Engage the 2 claws.

2. Install the 8 screws <B>.

INSTALL CONSOLE BOX

1. Engage the 2 claws and install the console box.

2. Install the bolt <B>.

3. Install the box bottom mat.

INSTALL FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY

INSTALL HEATER CONTROL ASSEMBLY (for LHD)

Note

Do not bend the cable when installing the heater control assembly.

1. Insert each cable into the instrument panel.

2. 

   Text in Illustration

   *1	Defroster Cable
   *2	Air Inlet Cable
   *3	Air Mix Cable

   Pass the white air inlet cable between the instrument panel and wire harness.

3. Pass the black air mix cable between the instrument panel and wire harness.

4. Pass the blue defroster cable between the instrument panel reinforcement and wire harness, and then outside the wire harness clamp.

5. 

   Engage the 2 claws and install the heater control assembly with the 2 screws.

INSTALL HEATER CONTROL ASSEMBLY (for RHD)

Note

Do not bend the cable when installing the heater control assembly.

1. Insert the cable into the instrument panel.

2. 

   Text in Illustration

   *1	Defroster Cable
   *2	Air Inlet Cable
   *3	Air Mix Cable

   Pass the white air inlet cable through the wire harness.

3. Pass the black air mix cable between the instrument panel and brace.

4. Pass the blue defroster cable between the instrument panel reinforcement and wire harness, and then outside the wire harness clamp.

5. 

   Engage the 2 claws and install the heater control assembly with the 2 screws.

SET HEATER CONTROL ASSEMBLY

Text in Illustration

*a	LHD
*b	RHD

1. Make sure that the levers are placed in the position shown in the illustration.

CONNECT DEFROSTER DAMPER CONTROL CABLE SUB-ASSEMBLY

1. 

   Text in Illustration

   *a	Mode Link
   *b	DEF
   *c	FACE
   *d	Front Side

   Turn the mode link to the DEF position.

2. Install the cable ring onto the motor link.

3. Hold the mode wheel knob of the heater control and install the defroster cable onto the clamp while pulling it in the direction indicated by arrow A.

   Note

   Make sure that the air mix lever knob operates correctly. Also, confirm that there is no reverse movement of the knob at either end.

CONNECT AIR MIX DAMPER CONTROL CABLE SUB-ASSEMBLY

1. 

   Text in Illustration

   *a	Temperature Control Link
   *b	COOL
   *c	WARM
   *d	Front Side

   Turn the temperature control link to the MAX-cool position.

2. Install the cable ring onto the temperature control link.

3. Hold the mode wheel knob of the heater control and install the mode cable onto the clamp while pulling it in the direction indicated by arrow A.

   Note

   Make sure that the air mix lever knob operates correctly. Also, confirm that there is no reverse movement of the knob at either end.

CONNECT AIR INLET DAMPER CONTROL CABLE SUB-ASSEMBLY

1. 

   Text in Illustration

   *a	LHD
   *b	RHD
   *c	Air Inlet Control Link
   *d	FRESH
   *e	RECIRCULATION
   *f	Front Side

   Turn the air inlet control link to the RECIRCULATION position.

2. Turn the air inlet control link to the FRESH AIR position.

3. Install the cable ring onto the air inlet control link.

4. Hold the air inlet lever knob of the heater control and install the air inlet cable onto the clamp while pulling it in the direction indicated by arrow A.

   Note

   Make sure that the air inlet lever knob operates correctly. Also, confirm that there is no reverse movement of the knob at either end.

INSTALL COWL SIDE TRIM BOARD LH

1. Engage the 2 clips and claw, and install the cowl side trim board LH.

INSTALL INSTRUMENT PANEL ASSEMBLY

INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY CENTER

1. Connect the connectors.

2. Engage the 4 clips and 3 claws and install the instrument cluster finish panel center.

3. Install the screw <B>.

4. Install the control knob.

INSTALL FRONT NO. 1 SPEAKER ASSEMBLY (w/o Power Window)

1. Connect the connector.

2. 

   Install the 2 screws.

INSTALL FRONT NO. 1 SPEAKER ASSEMBLY (w/ Power Window)

1. Connect the connector.

2. Install the front No. 1 speaker with the 2 screws.

INSTALL INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY NO. 2

1. Engage the 2 claws.

INSTALL FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

INSTALL FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

1. Install the front door opening trim weatherstrip.

INSTALL TACHOMETER ASSEMBLY (w/ Tachometer)

1. Install the tachometer with the bolt.

   Torque:

   6.5 N*m  { 66 kgf*cm, 58 in.*lbf }

2. Connect the connector.

INSTALL STEERING COLUMN UPPER COVER

1. Install the steering column cover upper, as shown in the illustration (w/ tachometer).

2. 

   While turning the steering wheel to the right and left, engage the 4 claws and install the steering column cover upper with the 2 screws.

   Torque:

   2.0 N*m  { 20 kgf*cm, 18 in.*lbf }

3. 

   Tighten the screw behind the tachometer (w/ tachometer).

   Note

   Tighten the screw if the tachometer has been extended and the column cover has been removed.

   Torque:

   9.0 N*m  { 92 kgf*cm, 80 in.*lbf }