FRONT AXLE HUB INSTALLATION


  1. INSTALL STEERING KNUCKLE


    1. A0137CU

      Fix the steering knuckle in a vise and temporarily install the bolt and nut. Then, using a screwdriver and hammer, widen the knuckle slit.

      Note


      • Do not widen the steering knuckle slit by more than 10 mm.


      • Do not damage the steering knuckle slit portion.

    2. A01392P

      Insert the convex portion of the shock absorber assembly front into the steering knuckle slit. In addition, make the bracket edge come into contact with the steering knuckle tip.

      Note

      Set the nut on the front side of the vehicle.

    3. A0138MW

      Release the screwdriver. Then tighten the nut to tighten the shock absorber assembly front steering knuckle.

      Torque:
      52 N*m  { 530 kgf*cm, 38 ft.*lbf }

    4. Remove any materials such as iron powder that adhere to the magnetic seal portion.

  2. INSTALL FRONT DRIVE SHAFT ASSEMBLY

    A0137MQ

    1. Coat the spline of the inboard joint shaft assembly with transaxle oil.

    2. Align the shaft splines and install the drive shaft assembly with a screwdriver and hammer.

      Note


      • Face the snap ring cut area downward.

      • Do not damage the oil seal.

      • Do not damage the front drive shaft assembly boot.

      Tech Tips

      Whether the front drive shaft assembly is securely driven in or not can be confirmed from the brass bar reaction force or sound.

  3. INSTALL FRONT AXLE ASSEMBLY


    1. Push the front axle assembly out of the vehicle to align the spline of the front drive shaft assembly with the front axle assembly and insert the front axle assembly.

      Note


      • Do not push the front axle assembly further out of the vehicle than is necessary.

      • Do not damage the oil seal.

      • Do not damage the front drive shaft assembly boot.

      • Do not damage the speed sensor rotor.

      • Check for any foreign matter on the speed sensor rotor and insertion part.

  4. INSTALL FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO.1

    A0136N3

    1. Push the front suspension lower arm No. 1 downward, install the front lower ball joint and tighten the castle nut and a new clip.

      Torque:
      98 N*m  { 1,000 kgf*cm, 72 ft.*lbf }

      Note

      Retighten the castle nut and clip within a turning angle of 60° after aligning the hole of the clip with the castle nut.

  5. INSTALL FRONT STABILIZER BAR

    A01388W

    1. Install the stabilizer bar front with the 2 cushion retainers, 2 cushions and a nut, as shown in the illustration.

      Note

      Be sure to install the cushion and retainer in the correct direction.

    2. Tighten the nut with a spanner (10 mm).

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

  6. INSTALL TIE ROD END SUB-ASSEMBLY

    A013608

    1. Connect the tie rod end to the steering knuckle and install it with the castle nut and a new cotter pin.

      Torque:
      33 N*m  { 336 kgf*cm, 24 ft.*lbf }

      Note

      Retighten the castle nut and cotter pin within a turning angle of 60° after aligning the hole of the cotter pin with the castle nut.

  7. INSTALL FRONT DISC BRAKE

    A0136MR

    1. Using "TORX" socket wrench T30, install the front disc with the screw.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  8. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

    A013828

    1. Install the front disc brake caliper assembly onto the steering knuckle with the 2 bolts.

      Torque:
      88 N*m  { 900 kgf*cm, 65 ft.*lbf }
    2. A013788

      Install the flexible hose onto the shock absorber assembly front with the bolt.

      Torque:
      29 N*m  { 300 kgf*cm, 22 ft.*lbf }

  9. INSTALL FRONT SPEED SENSOR


    1. A0136CZE02
      Text in Illustration
      *a Paint Line

      Connect the speed sensor wire to the shock absorber assembly front.

      Note

      Insert a rubber grommet into the bracket with the painted line placed between the bracket cutouts.

    2. A0136TN

      Install the bolt and the speed sensor front onto the steering knuckle.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

      Note


      • Do not damage the speed sensor.

      • Keep the speed sensor free of any foreign material.

      • Do not twist the sensor wire when installing the speed sensor.

  10. INSTALL FRONT AXLE HUB NUT

    A0135U4E01

    1. Install a new front axle hub nut.

      Torque:
      216 N*m  { 2,202 kgf*cm, 160 ft.*lbf }

    2. Using a hammer and chisel, stake the front axle hub nut.

  11. INSTALL FRONT WHEEL

    Torque:
    103 N*m  { 1,050 kgf*cm, 76 ft.*lbf }

  12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Torque:
    5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

  13. ADJUST FRONT WHEEL ALIGNMENT

    Click here

  14. CHECK ABS WARNING LIGHT

    Click here