OUTPUT SHAFT DISASSEMBLY


  1. REMOVE RELEASE FORK RETRACTING SPRING HANGER

    A01367T

    1. Remove the bolt and the release fork retracting spring hanger.

  2. REMOVE CLUTCH RELEASE BEARING ASSEMBLY

    A0138DD

    1. Remove the clutch release bearing from the clutch release fork.

  3. REMOVE CLUTCH RELEASE FORK LEVER

    A0135ZF

    1. Separate the torsion spring from the clutch release fork.

    2. A013743

      Using 2 screwdrivers and a hammer, tap the E-ring out.

    3. A01379J

      Pull the clutch release fork lever out of the transaxle case to remove the clutch release fork and then, release the fork torsion spring stopper and torsion spring from the clutch.

  4. REMOVE CLUTCH RELEASE FORK LEVER SHAFT OIL SEAL

    A01375E

    1. Using a screwdriver, remove the clutch release fork lever oil seal.

  5. REMOVE CLUTCH HOUSING COVER NO.1

    A013662

    1. Remove the clutch housing cover from the transaxle case.

  6. REMOVE FLOOR SHIFT CONTROL LEVER HOUSING SUPPORT BRACKET

    A01365I

    1. Remove the 2 bolts and cable control bracket from the transaxle case.

  7. REMOVE MANUAL TRANSAXLE CASE PLUG

    A0136MB

    1. Remove the manual transaxle case plug and gasket from the manual transaxle case.

  8. REMOVE BACK-UP LIGHT SWITCH ASSEMBLY


    1. A0136YL

      Separate the back-up light switch wire harness from the 2 clamps.

    2. A0138RE

      Using SST, remove the back-up light switch and gasket from the manual transmission case.

      SST
      09817-16011

  9. REMOVE LOCK BALL ASSEMBLY NO. 1

    A0136BH

    1. Remove the lock ball No. 1 from the manual transmission case.

  10. REMOVE SHIFT AND SELECT LEVER SHAFT ASSEMBLY

    A0136GU

    1. Remove the 4 bolts and shift and select lever shaft from the transmission case.

    2. Remove the select return compression spring from the transmission case.

  11. REMOVE REVERSE IDLER GEAR SHAFT BOLT

    A0136JQ

    1. Remove the reverse idler gear shaft bolt and gasket.

  12. REMOVE MANUAL TRANSMISSION CASE

    A0137FO

    1. Remove the 5 bolts from the manual transaxle case side.

    2. A0137UP

      Remove the 8 bolts from the manual transmission case side.

    3. Using a plastic hammer, remove the manual transmission case.

  13. REMOVE REVERSE IDLER GEAR SHAFT

    A013834

    1. Remove the reverse idler gear shaft from the transaxle case.

  14. REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY


    1. Remove the reverse idler gear from the transaxle case.

  15. REMOVE REVERSE SHIFT ARM BRACKET ASSEMBLY

    A01378G

    1. Remove the 2 bolts and the reverse shift arm bracket from the front transaxle case.

  16. REMOVE GEAR SHIFT FORK SHAFT NO.1

    A0138EB

    1. Remove the bolt from the gear shift fork No. 1.

    2. A0136O9

      Using a pin punch and hammer, remove the slotted spring pin from the gear shift head No. 1.

    3. A0136BU

      Remove the gear shift fork shaft No. 1, gear shift head No. 1 and gear shift fork No. 1.

    4. A013603

      Using 2 screwdrivers and a hammer, remove the snap ring from the gear shift fork shaft No. 1.

  17. REMOVE GEAR SHIFT FORK SHAFT NO.3

    A01365U

    1. Remove the straight pin from the gear shift fork No. 3.

    2. A0136BK

      Using a pin punch and hammer, remove the slotted spring pin from the gear shift head No. 3.

    3. A0136XZ

      Using 2 screwdrivers and a hammer, remove the snap ring from the gear shift fork shaft No. 3.

      Tech Tips

      Use a shop rag or piece of cloth to prevent the snap ring from flying off.

    4. A0136GP

      Remove the gear shift fork shaft No. 3, compression spring, gear shift head No. 3 and gear shift fork No. 3 from the front transaxle case.

    5. A0137PZ

      Using 2 screwdrivers and a hammer, remove the snap ring from the gear shift fork shaft No. 3.

      Tech Tips

      Use a shop rag or piece of cloth to prevent the snap ring from flying off.

  18. REMOVE GEAR SHIFT FORK SHAFT NO.2

    A0138MOE01

    1. Using a magnetic finger, remove the straight pin from the reverse shift fork.

    2. A0136EW

      Using 2 screwdrivers and a hammer, remove the snap ring from the gear shift fork shaft No. 3.

      Tech Tips

      Use a shop rag or piece of cloth to prevent the snap ring from flying off.

    3. A0136DA

      Remove the bolt from the gear shift fork No. 2.

    4. A0136B7

      Shift the gear shift fork No. 2 to the 4th gear range.

    5. Remove the gear shift fork shaft No. 2, gear shift fork No. 2 and reverse shift fork.

    6. A0136RG

      Using 2 screwdrivers and a hammer, remove the snap ring from the gear shift fork shaft No. 2.

      Tech Tips

      Use a shop rag or piece of cloth to prevent the snap ring from flying off.

  19. REMOVE INPUT SHAFT ASSEMBLY

    A0138L1

    1. Remove the input shaft assembly from the manual transaxle case.

  20. REMOVE OUTPUT SHAFT ASSEMBLY


    1. Remove the output shaft assembly from the manual transaxle case.

  21. REMOVE DIFFERENTIAL CASE ASSEMBLY

    A0138QQ

    1. Remove the differential case assembly from the front transaxle case.

  22. REMOVE OIL RECEIVER PIPE NO.2(MTM)

    A0138KTE01

    1. Remove the oil receiver pipe No. 2 from the manual transmission case.

      Note

      Do not damage the oil receiver pipe No. 2.

  23. REMOVE TRANSMISSION MAGNET

    A0138HO

    1. Remove the transmission magnet from the front transaxle case.

  24. REMOVE FRONT TRANSAXLE CASE OIL SEAL

    A013616

    1. Using a screwdriver, remove the front transaxle case oil seal.

  25. REMOVE OUTPUT SHAFT FRONT BEARING

    A0138KPE01

    1. Using SST, remove the output shaft front bearing (outer race) from the front transaxle case.

      SST
      09308-00010

  26. REMOVE OUTPUT SHAFT(MTM) COVER

    A0138WO

    1. Remove the output shaft cover from the transaxle case.

  27. REMOVE TRANSMISSION CASE OIL SEAL

    A01371Z

    1. Using a screwdriver, remove the transmission case oil seal.

  28. REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

    A0137BFE01

    1. Using SST, remove the front differential case rear tapered roller bearing and the shim.

      SST
      09950-60010   ( 09951-00560 )
      09950-70010   ( 09951-07200 )

  29. REMOVE TRANSAXLE CASE OIL SEAL

    A0137WK

    1. Using a screwdriver, remove the transaxle case oil seal from the transaxle case.

  30. REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

    A0135U3E01

    1. Using SST, remove the front differential case front tapered roller bearing.

      SST
      09387-00041   ( 09387-02010, 09387-02020 )

  31. REMOVE INPUT SHAFT REAR BEARING SHIM

    A013857

    1. Remove the input shaft rear bearing shim from the transmission case.

  32. REMOVE OUTPUT SHAFT REAR BEARING

    A0137SJE01

    1. Using SST, remove the output shaft rear bearing.

      SST
      09527-30010
      09612-65014   ( 09612-01030, 09612-01050 )

  33. REMOVE OUTPUT SHAFT REAR BEARING SHIM

    A0137B0

    1. Remove the output shaft rear bearing shim.

  34. REMOVE OUTPUT SHAFT REAR BEARING

    A0136W2E01

    1. Using SST and a press, remove the output shaft rear bearing.

      SST
      09950-60010   ( 09951-00220 )
      09950-70010   ( 09951-07100 )

  35. INSPECT 1ST GEAR THRUST CLEARANCE

    A0137ZK

    1. Using a feeler gauge, measure the 1st gear thrust clearance.

      Standard clearance
      0.10 to 0.35 mm (0.0039 to 0.0138 in.)
      Maximum clearance
      0.35 mm (0.0138)

  36. INSPECT 2ND GEAR THRUST CLEARANCE

    A0138I1

    1. Using a feeler gauge, measure the 2nd gear thrust clearance.

      Standard clearance
      0.10 to 0.55 mm (0.0039 to 0.0217 in.)
      Maximum clearance
      0.55 mm (0.0217)

  37. INSPECT 1ST GEAR RADIAL CLEARANCE

    A0138AJ

    1. Using a dial indicator, measure the 1st gear radial clearance.

      Standard clearance
      0.015 to 0.056 mm (0.0006 to 0.0022 in.)
      Maximum clearance
      0.056 mm (0.0022 in.)

      If the clearance exceeds the maximum, replace the 1st gear, needle roller bearing or shaft.

  38. INSPECT 2ND GEAR RADIAL CLEARANCE

    A0138TQ

    1. Using a dial indicator, measure the 2nd gear radial clearance.

      Standard clearance
      0.015 to 0.056 mm (0.0006 to 0.0022 in.)
      Maximum clearance
      0.056 mm (0.0022 in.)

      If the clearance exceeds the maximum, replace the 2nd gear, needle roller bearing or shaft.

  39. REMOVE COUNTER 5TH GEAR SHAFT SNAP RING

    A0136BZ

    1. Using 2 screwdrivers and a hammer, remove the counter 5th gear shaft snap ring from the output shaft.

  40. REMOVE 4TH DRIVEN GEAR

    A0138U8

    1. Using a press, remove the 5th driven gear and 4th driven gear from the output shaft.

  41. REMOVE OUTPUT SHAFT SPACER

    A01369A

    1. Remove the output shaft spacer from the output shaft.

  42. REMOVE 2ND GEAR

    A01380EE01

    1. Using SST and a press, remove the 3rd driven gear and 2nd gear from the output shaft.

      SST
      09950-00020

  43. REMOVE 2ND GEAR NEEDLE ROLLER BEARING

    A0136T6

    1. Remove the 2nd gear needle roller bearing from the output shaft.

  44. REMOVE 2ND GEAR BEARING SPACER

    A0136R0

    1. Remove the 2nd gear bearing spacer from the output shaft.

  45. REMOVE 2ND GEAR SYNCHRONIZER RING

    A0137ES

    1. Remove the 2nd gear synchronizer ring from the reverse gear.

  46. REMOVE CLUTCH HUB NO.1 SHAFT SNAP RING

    A0137OO

    1. Using a snap ring expander, remove the clutch hub No. 1 shaft snap ring from the output shaft.

      Tech Tips

      Do not damage the journal surface of the output shaft.

  47. REMOVE 1ST GEAR

    A01361F

    1. Using a press, remove the transmission clutch hub No. 1 and 1st gear from the output shaft.

  48. REMOVE 1ST GEAR NEEDLE ROLLER BEARING

    A0138NB

    1. Remove the 1st gear needle roller bearing from the output shaft.

  49. REMOVE OUTPUT SHAFT FRONT BEARING

    A01374YE01

    1. Using SST and a press, remove the output shaft front bearing from the output shaft.

      SST
      09950-00020

  50. REMOVE TRANSMISSION CLUTCH HUB NO.1

    A0135TT

    1. Remove the 2 shifting key springs No. 1, 3 shifting keys No. 1 and reverse gear from the transmission clutch hub No. 1.