CLUTCH PEDAL REMOVAL


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.

  2. REMOVE STEERING COLUMN COVER UPPER

    A0136OJE02

    1. Remove the 2 screws while turning the steering wheel to the right and left.

    2. Disengage the 4 claws and remove the steering column cover upper.

    3. A0136TV

      Remove the steering column cover upper, as shown in the illustration (w/ tachometer).

    4. A0136HY

      If the steering column cover upper is difficult to remove, loosen the screw behind the tachometer, pull up and extend the tachometer, and then remove the steering cover upper (w/ tachometer).

  3. REMOVE TACHOMETER (w/ TACHOMETER)

    A0135U6

    1. Disconnect the connector.

    2. Remove the bolt and tachometer.

  4. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    A01380D

    1. Separate the front door opening trim weatherstrip LH.

  5. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

  6. REMOVE FRONT PILLAR GARNISH RH

    A0138EW

    1. Disengage the 2 clips and 2 claws, and remove the front pillar garnish.

    2. A0138GXE01

      Completely cover the airbag with a piece of cloth or nylon of 700 mm (27.56 in.) x 120 mm (4.72 in.) and fix the ends of the cover with adhesive tape, as shown in the illustration.

      Note

      Cover the curtain shield airbag with the protective cover as soon as the front pillar garnish is removed.

  7. REMOVE FRONT PILLAR GARNISH LH

  8. REMOVE INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY NO. 1

    A0136QKE01

    1. Disengage the 2 claws.

  9. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

    A01362K

    1. Remove the 2 screws.

    2. A0136BT

      Disconnect the connector.

  10. REMOVE INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY NO. 2

  11. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

  12. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

    A0136KWE01

    1. Remove the control knob.

    2. Remove the screw <B>.

    3. Disengage the 4 clips and 3 claws and remove the cluster finish panel by pulling it up from underneath.

    4. Disconnect the connectors and remove the instrument cluster finish panel center.

  13. REMOVE INSTRUMENT PANEL ASSEMBLY

    A0136KRE02

    1. Disengage the 2 claws and open the cover.

    2. A0138UJ

      Disconnect the airbag connector, as shown in the illustration.

    3. Remove the bolt <A>, 2 nuts <D> and 2 screws <B>.

      A0137GXE01

    4. Disengage the 4 clips and 5 claws and remove the instrument panel assembly.

      A0138IQ

  14. REMOVE COWL SIDE TRIM BOARD LH


    1. A0137W2E01

      Disengage the 2 clips and claw, and remove the cowl side trim board LH.

  15. REMOVE COWL SIDE TRIM BOARD RH

  16. REMOVE HEATER CONTROL ASSEMBLY (LHD)

    A0136DQE05

    Note

    Do not bend the cable when removing the heater control assembly.


    1. Separate the black air mix cable from the clamp and remove the cable ring from the temperature control link.

    2. Separate the white air inlet cable from the clamp and remove the cable ring from the air inlet control link.

    3. Separate the blue defroster cable from the clamp and remove it from the mode link.

    4. Remove the 2 screws, disengage the 2 claws and remove the heater control assembly.

  17. REMOVE HEATER CONTROL ASSEMBLY (RHD)

    A01389IE04

    Note

    Do not bend the cable when removing the heater control assembly.


    1. Separate the black air mix cable from the clamp and remove the cable ring from the temperature control link.

    2. Separate the white air inlet cable from the clamp and remove the cable ring from the air inlet control link.

    3. Separate the blue defroster cable from the clamp and remove it from the mode link.

    4. Remove the 2 screws, disengage the 2 claws and remove the heater control assembly.

  18. REMOVE CONSOLE BOX

    A0137LLE01

    1. Remove the shift knob.

    2. Remove the box bottom mat.

    3. Remove the bolt <E>.

    4. Disengage the 2 claws and remove the console box.

  19. REMOVE INSTRUMENT PANEL ASSEMBLY LOWER

    A0138HB

    1. Disconnect the antenna cord by disengaging the 4 fastenings.

    2. Disconnect the connectors and 3 wire harness clamps.

    3. Remove the 2 bolts <F>, 5 screws <I> or <H>, screw <G>, screw <J> and 2 clips and remove the instrument panel lower.

      A01388AE01

  20. REMOVE STOP LIGHT SWITCH ASSEMBLY (LHD)


    1. Disconnect the connector from the stop light switch.

    2. Turn the stop light switch counterclockwise, and remove the stop light switch.

    3. Remove the stop light switch mounting adjuster from the pedal support.

  21. SEPARATE CLUTCH RELEASE CABLE ASSEMBLY

    A01391EE01

    1. Turn and loosen the clutch release cable adjusting nut.

    2. A0137Q6E01

      Separate the clutch release cable from the clutch pedal.

  22. SEPARATE MASTER CYLINDER PUSH ROD CLEVIS (LHD)

    A0135YT

    1. Remove the clip and push rod pin, and separate the push rod clevis.

  23. SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY (RHD)


    1. A01387X

      Secure the steering wheel with the seat belt in order to prevent rotation and damage to the spiral cable.

    2. Remove the steering column hole cover plate from the floor.

    3. A0135UXE01

      Put matchmarks on the sliding yoke and intermediate shaft.

    4. Loosen bolt A and remove bolt B to separate the sliding yoke.

  24. REMOVE BRAKE PEDAL SUPPORT SUB-ASSEMBLY (LHD)


    1. Disconnect the 2 clamps of the wire harness from the pedal support.

    2. Disconnect the 2 clamps of the wire harness from the stud bolt.

    3. A01392NE02

      Remove the 4 nuts, 2 bolts and pedal support.

    4. A0137PQ

      Remove the nut from the pedal support.

    5. A0136VI

      Remove the bush from the pedal support.

  25. REMOVE CLUTCH PEDAL SUPPORT SUB-ASSEMBLY (RHD)


    1. A0135UEE01

      Remove the 2 nuts, 2 bolts and pedal support.

    2. A0135V5

      Remove the bush from the pedal support.

  26. REMOVE CLUTCH PEDAL SUB-ASSEMBLY


    1. Using a 13 mm socket wrench, remove the nut and bolt.

    2. LHD:


      1. Remove the clutch pedal and brake pedal from the pedal support.

    3. RHD:


      1. Remove the clutch pedal from the pedal support.

    4. Remove the collar and bush from the clutch pedal.

    5. LHD:


      1. Remove the collar and bush from the brake pedal.

    6. Remove the pedal pad.