SFI SYSTEM (w/ Electronic Throttle Control System) DTC CHECK / CLEAR

CHECK DTC

Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester ON.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Check DTCs and freeze frame data, and then write them down.

Tech Tips

If you need help when using the intelligent tester, refer to the instruction manual.

Confirm the details, referring the DTC chart.

Tech Tips

Multiple failure detection list

Malfunction	Regularly output DTC	Possibly output DTC	Engine condition
Open or short in injector circuit	P0261 or P0262 P0264 or P0265 P0267 or P0268	P0301, P0300 P0302, P0300 P0303, P0300	Rough idle
Open or short in igniter circuit	P0301 P0302 P0303	-	Rough idle
Misfire	P0301 P0302 P0303 P0300	-	Rough idle
Open or short manifold absolute pressure sensor circuit	P0107 or P0108	-	Rough idle or lack of power
Manifold absolute pressure sensor characteristic	P0106	P0171, P0172	Rough idle or lack of power
Air leakage intake system after throttle	-	P0106, P0606 (rare case)	High idle engine speed
Fuel system	P0171, P0172	P0300, P0301, P0302, P0303	High idle engine speed
Engine speed sensor	P0335	-	Does not start
EEPROM (inside ECM)	P0603	P2109 (This DTC also output when new ECM installed), P1127	Does not start
Accelerator pedal position sensor characteristic	P2138	-	Lack of power
ETCS throttle position sensor characteristic	P0121 or P0221	P0106	-
Open or short in throttle position sensor circuit	P0122, P0123, P0222 or P0223	P2109 (This DTC also output when new ECM installed), P1127	-
Open in ETCS throttle drive line	P2111	P2109 (This DTC also output when new ECM installed), P2109 (ETCS initialization triggered)	-
This DTC also output when new ECM installed	-	P1127 (ETCS initialization triggered), P2112	-
Short in ETCS throttle drive line	P2100 or P2111	P1127 (ETCS initialization triggered), P2112, P2109	-
ETCS throttle valve stiff or sticking	P2111	P2109 (This DTC also output when new ECM installed), P1127, P0120, P2112, P2100 (rare case)	-
ETCS throttle return spring (cannot closed)	P2119	P2109 (This DTC also output when new ECM installed, ETCS initialization triggered), P1127 (ETCS initialization triggered)	-
ETCS throttle return spring (cannot opened)	P2112	P2111	-
ETCS throttle mechanical stop performance (throttle closing performance)	P2109 (This DTC also output when new ECM installed)	-	-
ETCS initialization does not complete	P1127	-	-
ETCS throttle opener position was changed from previously (This indicates ECM detects that throttle has been replaced)	P0120	-	-
ECM	P06076	-	-

FREEZE FRAME DATA
1. Connect the intelligent tester to the DLC3.
2. Turn the ignition switch to ON and turn the intelligent tester ON.
3. Read DTCs by selecting the following menu items: Powertrain / Engine and ECT / DTC.
4. Select a parameter(s) to check the freeze frame data.
5. Note down the DTC(s) and freeze frame data.
  
  Tech Tips
  
  If you need help when using the intelligent tester, refer to the instruction manual.
CLEAR DTC AND FREEZE FRAME DATA (using the intelligent tester)
1. Connect the intelligent tester to the DLC3.
2. Turn the ignition switch to ON (do not start the engine) and turn the intelligent tester ON.
3. Select the following menu items: Powertrain / Engine and ECT / DTC / Clear.
4. Erase DTCs and freeze frame data by pressing the YES button on the tester.
  
  Tech Tips
  
  If you need help when using the intelligent tester, refer to the instruction manual.
CLEAR DTC AND FREEZE FRAME DATA (not using the intelligent tester)
1. Remove the EFI fuse from the engine room R/B for more than 60 seconds, or disconnect the negative battery cable for more than 60 seconds. When disconnecting the negative battery cable, perform the "INITIALIZE" procedure.