ТРОС МЕХАНИЗМА ВЫБОРА И ПЕРЕКЛЮЧЕНИЯ ПЕРЕДАЧ УСТАНОВКА


  1. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    1. A01BA7Z

      Pass the control cable assembly through the floor hole.

    2. Install the transmission control cable assembly with the 2 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
    3. A01BC69

      Wide body LHD steering position type:


      1. Install the control cable bracket No.3 to the transmission control cable assembly.

      2. Install the control cable bracket No.3 with the 2 nuts.

        Torque:
        5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
    4. A01BDF2

      Install the front floor footrest with the 2 nuts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }
    5. A01BCUGE01

      Install the transmission control cable assembly to the shift lever.

      Note

      Install the transmission control cable assembly so that the end section of the select cable indicated by the arrow, as shown in the side view, (A in the illustration) faces upward.

    6. A01BGLKE01

      Turn the control cable assembly adjust nut clockwise 180°. While holding the adjust nut, push in the locks.

    7. Install the control cable assembly to the shift lever.

      Tech Tips

      When the cable is installed to the shift lever, the locks are released and the adjust nut rotates 180°. Then, the locks are engaged again.

      Note

      Make sure that the control cable assembly is firmly installed to the shift lever.

  2. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY


    1. A01BC42

      Install the control cable bracket No.2 to the transmission control cable assembly.

    2. Install the control cable bracket No.2 with the 2 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
    3. A01BAIN

      Install the clamp with the bolt.

      Torque:
      14 N*m  { 143 kgf*cm, 10 ft.*lbf }
    4. A01BECK

      Install the control cable support to the control cable assembly.

    5. Install the control cable support with the bolt.

      Torque:
      14 N*m  { 143 kgf*cm, 10 ft.*lbf }
    6. A01BEMCE01

      Install new 2 clips to the control cable bracket No.1.

    7. Install the transmission control cable assembly to the control cable bracket No.1.

      Note


      • Be sure that A claws of the clips are firmly engaged into the bracket grooves.

      • Be sure the cable is set in the clip with both B claws erected to prevent slippage of the cable in the opposite direction.

    8. A01BG2ME01

      Align the matchmarks on the control cable assembly and the outer lever.

    9. Install the transmission control cable assembly to the outer lever with the 2 nuts.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

  3. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER


    1. A01BB5ME01

      Установите нижнюю центральную отделочную накладку панели приборов и закрепите ее 8 захватами.

  4. INSTALL SHIFTING HOLE COVER ASSEMBLY


    1. A01BF5BE01

      Механическая трансмиссия:

      Установите чехол лючка рычага переключения передач в сборе и введите в зацепление 6 захватов.

    2. Автоматическая трансмиссия:

      Установите чехол лючка рычага переключения передач в сборе и введите в зацепление 8 захватов.

  5. INSTALL SHIFT LEVER KNOB

  6. INSTALL PARKING BRAKE HOLE COVER


    1. A01BF1ME01

      Установите крышку отверстия стояночного тормоза и введите в зацепление 6 захватов.

  7. INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY NO.1


    1. A01BE86E01

      Введите в зацепление 3 захвата.

    2. Установите нижнюю крышку панели приборов № 1 в сборе и закрепите ее 2 фиксаторами.

  8. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER


    1. A01BHMVE01

      Введите в зацепление 4 фиксатора (B).

    2. Установите нижнюю отделочную накладку панели приборов и закрепите ее 2 фиксаторами (A).

  9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

  10. PERFORM INITIALIZATION

    Some systems need initialization after reconnecting the cable to the negative battery terminal Click here.