ТРОС МЕХАНИЗМА ПЕРЕКЛЮЧЕНИЯ ПЕРЕДАЧ УСТАНОВКА


  1. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    1. Rolled up the floor carpet of the front seat LH and connect the transmission control cable assembly with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 70 in.*lbf }

    2. Install the transmission control cable bracket No. 3 to the body with the 2 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 48 in.*lbf }

    3. Install the transmission control cable assembly to the transmission control cable bracket No. 3.

    4. A01BA7KE03
      Text in Illustration
      *a Cable End
      *b Protrusion

      Connect the cable end to the shift lock control unit.

      Note


      • Securely connect the cable end until if fits securely against the base of the pin.

      • Connect the cable end with the protrusion facing the front of the vehicle.

    5. A01BE5LE04
      Text in Illustration
      *1 Nut
      *2 Unit Housing
      *3 Spring
      *a Protrusion

      Turn the nut on the transmission control cable counterclockwise unit it stops it in place.

    6. Connect the transmission control cable to the shift lock control unit housing.

      Note


      • Connect the cable outer with the protrusion on the bottom.

      • Ensure that the groove on the cable outer is securely fitted to the shift lock control unit housing.

      • Ensure that the spring is positioned as show in the illustration.

  2. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER


    1. A01BB5ME01

      Установите нижнюю центральную отделочную накладку панели приборов и закрепите ее 8 захватами.

  3. INSTALL PARKING BRAKE HOLE COVER


    1. A01BF1ME01

      Установите крышку отверстия стояночного тормоза и введите в зацепление 6 захватов.

  4. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER


    1. A01BHMVE01

      Введите в зацепление 4 фиксатора (B).

    2. Установите нижнюю отделочную накладку панели приборов и закрепите ее 2 фиксаторами (A).

  5. INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY NO. 1


    1. A01BE86E01

      Введите в зацепление 3 захвата.

    2. Установите нижнюю крышку панели приборов № 1 в сборе и закрепите ее 2 фиксаторами.

  6. INSTALL SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY


    1. A01BF5BE01

      Механическая трансмиссия:

      Установите чехол лючка рычага переключения передач в сборе и введите в зацепление 6 захватов.

    2. Автоматическая трансмиссия:

      Установите чехол лючка рычага переключения передач в сборе и введите в зацепление 8 захватов.

  7. INSTALL SHIFT LEVER KNOB

  8. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY


    1. Install the transmission control cable bracket No. 2 to the under body with the 2 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 48 in.*lbf }

    2. Install the transmission control cable assembly to the transmission control cable bracket No. 2.

    3. Install the transmission control cable assembly with the 2 bolts.

      Torque:
      14 N*m  { 143 kgf*cm, 10 ft.*lbf }

    4. Install the transmission control cable assembly to the control shaft lever and transmission control cable bracket No.1 with a clip and the nut.

      Torque:
      15 N*m  { 150 kgf*cm, 11 ft.*lbf }

  9. ADJUST SHIFT LEVER POSITION


    1. A01BGSR

      Remove a clip, nut, and disconnect between the control shaft lever to transmission control cable assembly from the control shaft lever and transmission control cable bracket No. 1.

    2. A01BBPPE06

      Turn the control shaft lever until stop to a clockwise direction, return the control shaft lever 2 notches to N position.

    3. A01BEYV

      Set the shift lever to N position while holding the shift lever lightly toward the R position side and install it.

      Torque:
      15 N*m  { 150 kgf*cm, 11 ft.*lbf }

    4. Inspect the operation condition and work.

  10. INSPECT SHIFT LEVER POSITION


    1. When shifting from P position only with ignition switch ON and depress the break pedal.

    2. Make sure that the shifting lever moves smoothly and can be moderately operated.

    3. When starting engine, make sure that the vehicle moves forward when shifting from N to D position and moves reward when shifting R position.

  11. INSTALL ENGINE UNDER COVER NO. 1


    1. Install the No. 1 engine under cover with the 4 bolts.

      Torque:
      13 N*m  { 133 kgf*cm, 10 ft.*lbf }