ТРОС МЕХАНИЗМА ПЕРЕКЛЮЧЕНИЯ ПЕРЕДАЧ УСТАНОВКА


  1. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    1. Rolled up the floor carpet of the front seat LH and connect the transmission control cable assembly with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    2. Install the transmission control cable bracket No. 3 to the body with the 2 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    3. Install the transmission control cable assembly to the transmission control cable bracket No. 3.

    4. Turn the nut of the transmission control cable assembly approximately 180° counterclockwise. While holding the nut in place, securely push the stopper in all the way.

      A01BC86E06
      Text in Illustration
      *1 Stopper *2 Nut
      *a Push in - -

      Note

      Do not over-rotate the nut as it will come off the internal spring and the transmission control cable assembly will not be reusable.

    5. Install the outer part of the transmission control cable assembly to the shift lock control unit assembly. Check that the spring is positioned at "A" and push in the stopper.

      A01BB8KE01
      Text in Illustration
      *1 Shift Lock Control Unit Assembly *2 Spring
      *3 Stopper - -
      *a Push in - -

      Note

      Ensure that the groove on the transmission control cable assembly is securely fitted to the shift lock control unit assembly.

      Tech Tips

      If the stopper cannot be pushed in, slightly turn the nut clockwise and then push in the stopper again.

    6. A01BHM9E01
      Text in Illustration
      *a Protrusion

      Connect the end of the transmission control cable assembly to the shift lock control unit assembly.

      Note


      • Securely connect the cable end until if fits securely against the base of the pin.

      • Connect the cable end with the protrusion facing the front of the vehicle.

  2. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER


    1. Введите в зацепление 8 захватов, чтобы установить нижнюю центральную отделочную накладку панели приборов.

  3. INSTALL PARKING BRAKE HOLE COVER


    1. Введите в зацепление 6 захватов, чтобы установить крышку отверстия стояночного тормоза.

  4. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER


    1. Подсоедините трос устройства блокировки топливной крышки и трос управления замком капота к нижней отделочной накладке панели приборов.

    2. Установите нижнюю отделочную накладку панели приборов и закрепите ее 4 фиксаторами.

    3. Установите 2 фиксатора.

  5. INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY NO. 1


    1. Введите в зацепление 3 захвата, чтобы установить нижнюю крышку панели приборов № 1.

    2. Установите 2 фиксатора.

  6. INSTALL FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY


    1. Attach the 8 claws to install the floor shift position indicator housing sub-assembly.

  7. INSTALL SHIFT LEVER KNOB


    1. A01BE88

      Install the shift lever knob and twist it in the direction indicated by the arrow.

  8. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY


    1. Install the transmission control cable bracket No. 2 to the under body with the 2 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    2. Connect the transmission control cable assembly to the transmission control cable bracket No. 2.

    3. Install the transmission control cable assembly with the 2 bolts.

      Torque:
      14 N*m  { 143 kgf*cm, 10 ft.*lbf }

    4. Connect the transmission control cable assembly to the control shaft lever and transmission control cable bracket No. 1 with a clip and the nut.

      Torque:
      15 N*m  { 148 kgf*cm, 11 ft.*lbf }

  9. ADJUST SHIFT LEVER POSITION


    1. A01BGSR

      Remove a clip, nut, and disconnect between the control shaft lever to transmission control cable assembly from the control shaft lever and transmission control cable bracket No. 1.

    2. A01BBPPE06

      Turn the control shaft lever until stop to a clockwise direction, return the control shaft lever 2 notches to N position.

    3. A01BEYV

      Set the shift lever to N position while holding the shift lever lightly toward the R position side and install it.

      Torque:
      15 N*m  { 150 kgf*cm, 11 ft.*lbf }

    4. Inspect the operation condition and work.

  10. INSPECT SHIFT LEVER POSITION


    1. When shifting from P position only with ignition switch ON and depress the break pedal.

    2. Make sure that the shifting lever moves smoothly and can be moderately operated.

    3. When starting engine, make sure that the vehicle moves forward when shifting from N to D position and moves reward when shifting R position.

  11. INSTALL NO. 1 ENGINE UNDER COVER


    1. Install the No. 1 engine under cover with the 4 bolts.

      Torque:
      13 N*m  { 133 kgf*cm, 10 ft.*lbf }