СТАРТЕР (для моделей мощностью 2,0 кВт) ПРОВЕРКА


  1. INSPECT STARTER ARMATURE ASSEMBLY


    1. A01BBJUE01

      Using an ohmmeter, check that there is continuity between the segments of the commutator.

      If there is no continuity between any segment, replace the starter armature.

    2. A01BH2LE01

      Using an ohmmeter, check the resistance between the commutator and armature coil core.

      Standard resistance
      10 kΩ or higher

      If the result is not as specified, replace the starter armature.

    3. A01BB9P

      Check for the commutator circuit runout.


      1. Place the commutator on V-blocks.

      2. Using a dial indicator, measure the circle runout.

        Maximum runout
        0.05 mm (0.002 in.)

        If the runout is greater than the maximum, replace the starter armature.

    4. A01BAIZ

      Using vernier calipers, measure the commutator diameter.

      Standard diameter
      35.0 mm (1.378 in.)
      Minimum diameter
      34.0 mm (1.339 in.)

      If the diameter is less than the minimum, replace the armature.

    5. A01BGJB

      Check that the undercut portion between the segments is free of foreign objects and measure its depth.

      Standard undercut depth
      0.7 mm (0.028 in.)
      Minimum undercut depth
      0.2 mm (0.008 in.)

      If the undercut depth is less than the minimum, correct it with a hacksaw blade.

  2. INSPECT STARTER YOKE ASSEMBLY


    1. A01BGO2

      Using an ohmmeter, check that there is continuity between the terminal C wire and brushes.

      If there is no continuity, replace the starter yoke assembly

    2. A01BCD3E01

      Using an ohmmeter, check the resistance between the shunt coil terminals (A) and (B).

      Standard resistance
      1.5 to 1.9 Ω

      If the result is not as specified, replace the starter yoke assembly.

  3. INSPECT STARTER BRUSH HOLDER ASSEMBLY


    1. A01BBM8E01

      Using vernier calipers, measure the brush length.

      Standard length
      15.0 mm (0.591 in.)
      Minimum length
      9.0 mm (0.354 in.)

      If the length is less than the minimum, replace the brush holder assembly and starter yoke.

    2. A01BCAFE01

      Check the pull scale reading as soon as the brush spring is separated from the brush.

      Standard spring load
      21.5 to 27.5 N (2.2 to 2.8 kgf, 4.8 to 6.2 lbf)
      Minimum spring load
      12.7 N (1.3 kgf, 2.9 lbf)

      If the spring load is less than the minimum, replace the brush holder assembly.

    3. A01BB12E01

      Using an ohmmeter, measure the resistance between the positive (+) and negative (-) brush holders.

      Standard resistance
      10 kΩ or higher

      If the result is not as specified, repair or replace the brush holder assembly.

  4. INSPECT STARTER CLUTCH SUB-ASSEMBLY


    1. A01BHVEE01

      Turn the clutch pinion gear clockwise and check that it turns freely. Try to turn the clutch pinion gear counterclockwise and check that it locks. If necessary, replace the starter clutch.

  5. INSPECT MAGNET STARTER SWITCH ASSEMBLY


    1. A01BE2KE01

      Using an ohmmeter, check that there is continuity between terminals 50 and C.

      If there is no continuity, replace the magnet starter switch assembly.

    2. A01BEXLE01

      Using an ohmmeter, check that there is continuity between terminal 50 and the magnet switch body.

      If there is no continuity, replace the magnet starter switch assembly.