ДВИГАТЕЛЬ ПРОВЕРКА БЕЗ СНЯТИЯ С АВТОМОБИЛЯ


  1. INSPECT COOLANT

    Click here

  2. INSPECT ENGINE OIL

    Click here

  3. INSPECT BATTERY SPECIFIC GRAVITY

    Click here

  4. INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY


    1. Remove the air cleaner filter element from the air cleaner case sub-assembly.

    2. Visually check that there is no dirt, clog, and damage to the air cleaner filter element.

      Tech Tips


      • If there is any dirt or clog on the air cleaner filter element, clean it with compressed air.

      • If any dirt or clog remains even after cleaning the air cleaner element with compressed air, replace it.

  5. INSPECT VANE PUMP V BELT


    1. A01BGFTE01

      Check the V belt deflection.


      1. Belt deflection

        Pressing force
        98 N (10 kgf, 22 *lbf)

        New belt

        mm (in.)

        Used belt

        mm (in.)

        7.5 to 9.5

        (0.30 to 0.37)

        9.0 to 13

        (0.35 to 0.51)

      2. Tension

        New belt

        N (kgf)

        Used belt

        N (kgf)

        441 to 539

        (45 to 55)

        245 to 343

        (25 to 35)

        Note


        • Check the drive belt deflection at the specified point.

        • When installing a new belt, set its tension value as specified.

        • When checking a belt used for over 5 minutes, confirm the deflection value is within the specified range.

        • When reinstalling a belt used for over 5 minutes, perform the check based on the used deflection value.

        • V belt tension and deflection value should be checked after two revolution of engine cranking.

        • When using a belt tension gauge, confirm the accuracy first by using a master gauge.

  6. INSPECT V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1 (W/ AIR CONDITIONING)


    1. A01BBWCE01

      Check the V belt deflection.


      1. Belt deflection

        Pressing force
        98 N (10 kgf, 22 *lbf)

        New belt

        mm (in.)

        Used belt

        mm (in.)

        11 to 15

        (0.43 to 0.59)

        15 to 20

        (0.59 to 0.79)

      2. Tension

        New belt

        N (kgf)

        Used belt

        N (kgf)

        372 to 608

        (38 to 62)

        196 to 392

        (20 to 40)

        Note


        • Check the drive belt deflection at the specified point.

        • When installing a new belt, set its tension value as specified.

        • When checking a belt used for over 5 minutes, confirm the deflection value is within the specified range.

        • When reinstalling a belt used for over 5 minutes, perform the check based on the used deflection value.

        • V belt tension and deflection value should be checked after two revolution of engine cranking.

        • When using a belt tension gauge, confirm the accuracy first by using a master gauge.

  7. INSPECT FAN & GENERATOR V BELT


    1. A01BC2OE01

      Check the V belt deflection. (Per 1 belt)


      1. Belt deflection

        Pressing force
        98 N (10 kgf, 22 *lbf)

        New belt

        mm (in.)

        Used belt

        mm (in.)

        7.0 to 10

        (0.28 to 0.39)

        10 to 14

        (0.39 to 0.55)

      2. Tension (Per 1 belt)

        New belt

        N (kgf)

        Used belt

        N (kgf)

        441 to 539

        (45 to 55)

        196 to 343

        (20 to 35)

        Note


        • Check the drive belt deflection at the specified point.

        • When installing a new belt, set its tension value as specified.

        • When checking a belt used for over 5 minutes, confirm the deflection value is within the specified range.

        • When reinstalling a belt used for over 5 minutes, perform the check based on the used deflection value.

        • V belt tension and deflection value should be checked after two revolution of engine cranking.

        • When using a belt tension gauge, confirm the accuracy first by using a master gauge.

  8. INSPECT INJECTION TIMING


    1. A01BHFJ

      Using a mirror, check that the matchmarks of the injection pump flange and the timing gear case are aligned.

  9. ADJUST INJECTION TIMING


    1. A01BHMC

      Loosen the following nuts and bolts.


      1. Bolt holding the injection pump to the injection pump stay.

      2. 2 nuts holding the injection pump to the timing gear case.

    2. Align the matchmark by slightly tilting the injection pump.

    3. Tighten the following nuts and bolts.


      1. 2 nuts holding the injection pump to the timing gear case.

        Torque:
        21 N*m  { 210 kgf*cm, 15 ft.*lbf }

      2. Bolt holding the injection pump to the injection pump stay.

        Torque:
        26 N*m  { 270 kgf*cm, 19 ft.*lbf }

  10. INSPECT ENGINE IDLE SPEED


    1. Warm up the engine.

    2. When using an intelligent tester:


      1. Connect the intelligent tester to the DLC3.

        Idle speed
        720 to 820 rpm (A/C OFF)
        750 to 850 rpm (A/C ON)

        Tech Tips

        Refer to the intelligent tester operator's manual for further details.

    3. A01BAF6E02

      When not using an intelligent tester:


      1. Using SST, connect the tachometer test probe to terminal 9 (TAC) of the DLC3.

        SST
        09843-18040

      2. Check the idle speed.

        Idle speed
        720 to 820 rpm (A/C OFF)
        750 to 850 rpm (A/C ON)

        Note

        Switch off all accessories.

  11. INSPECT MAXIMUM ENGINE SPEED


    1. Start the engine.

    2. Depress the accelerator pedal all the way.

    3. Check the maximum speed.

      Maximum speed
      4,850 to 4,950 rpm

  12. INSPECT COMPRESSION

    Tech Tips

    If there is a lack of power, excessive oil consumption or poor fuel economy is suspected. Measure the compression pressure.


    1. Warm up and stop the engine.

    2. Remove the glow plugs. Click here

    3. Disconnect the spill control valve connector.

    4. Check the cylinder compression pressure.

      Tech Tips

      Turn the starter before measuring the compression pressure and remove the foreign objects.

    5. A01BGGZE01

      Install SST (attachment) to the glow plug hole.

      SST
      09992-00025   ( 09992-00121 )
      Torque:
      13 N*m  { 133 kgf*cm, 10 ft.*lbf }
    6. A01BAY4E01

      Connect SST (compression gauge) to the SST (attachment).

      SST
      09992-00025   ( 09992-00211 )

    7. Fully open the throttle valve, and start the engine.

    8. While cranking the engine, measure the compression pressure.

      Tech Tips

      Always use a fully charged battery to obtain engine revolution of 250 rpm or more.

    9. Repeat steps (a) through (d) for each cylinder.

      Note

      This measurement must be done as quickly as possible.

      Compression pressure
      3,138 kPa (32.0 kgf/cm2, 455 psi) or more
      Minimum pressure
      1,961 kPa (20.0 kgf/cm2, 284 psi)
      Difference between each cylinder
      490 kPa (5.0 kgf/cm2, 71 psi) or less

    10. If the cylinder compression in one or more cylinders is low, pour a small amount of engine oil into the cylinder through the glow plug hole and repeat steps (a) through (d) for the cylinder with low compression.


      1. If adding oil helps the compression, the piston rings and/or cylinder bore may be worn or damaged.

      2. If pressure stays low, a valve may be stuck or the seating may be improper, or there may be leakage past the gasket.

    11. Remove the SST.

    12. Reinstall the glow plugs. Click here

    13. Reconnect the spill control valve connector.