Click here

СИСТЕМА ECD Brake Override System

Click here
Click here
DTC Code DTC Name
  Brake Override System
Click here

DESCRIPTION

When the vehicle is being driven, depressing the accelerator pedal and brake pedal will activate the brake override system to restrict driving torque. The conditions for activating the brake override system as well as the items that are controlled are explained below.

Activation Conditions:
Note:

The vehicle may not enter the brake override system control due to the relation of the accelerator pedal angle and the vehicle's speed.

Items Controlled:
Deactivation Conditions:
Click here

INSPECTION PROCEDURE

Inspection Method

Example:

Drive at 10 km/h (6.25 mph), depress the accelerator pedal by 1/2 to 3/4 and keep it in that position. Under these conditions, if the engine speed decreases to 1000 rpm when the brake pedal is depressed, then the brake override system has been activated.

CAUTION:

When carrying out the inspection, use a place where you are able to carry it out safely and also pay close attention to your surroundings.

Also, when driving, make absolutely sure that all road traffic laws, such as speed limits, are observed.

Tip:

  • Under normal conditions, the Accelerator Position value changes in response to the Accel Sens. No. 1 Volt % value. For more information on the numerical values, refer to the Data List (Click here).

  • If the Accelerator Position in the Data List and Accel Sens. No. 1 Volt % values diverge and the Accelerator Position value in the Data List is fixed even though Accel Sens. No. 1 Volt % is changing, check that this control is activated (use the GTS data saving function to record data while driving the vehicle, and then confirm it after driving is completed).

Note:

The brake override system restricts driving torque if the brake pedal is depressed when driving with the accelerator pedal depressed. If a customer reports experiencing loss of torque after the accelerator and brake pedals have both been intentionally depressed, explain to the customer that this is not a malfunction, and that the customer should avoid depressing both the accelerator and brake pedals at the same time.

Example: While operating the accelerator pedal, the customer uses their left foot to operate the brake pedal.

Click here

PROCEDURE


  1. Click here

    CHECK DTC OUTPUT


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Enter the following menus: System Select / Health Check.

    4. Check DTCs.

      Table 1. Result
      Result Proceed to
      No DTC is output A
      DTC is output B

  2. Click here

    READ VALUE USING GTS (STOP LIGHT SWITCH)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.

    4. Check the Data List indication when the brake pedal is depressed and released.

      OK
      Tester Display Condition Specified Condition
      Stop Light Switch Brake pedal released OFF
      Brake pedal depressed ON

  3. Click here

    INSPECT BRAKE PEDAL


    1. Inspect and adjust the brake pedal (Click here).

      Tip:

      If the stop light switch turns ON too late, the start of brake override system control may be delayed; if it turns ON too soon, brake override system control may begin too early, so conduct inspection of the brake pedal and stop light switch.


  4. Click here

    READ VALUE USING GTS (ACCELERATOR PEDAL POSITION SENSOR)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No. 1 Volt % and Accel Sens. No. 2 Volt %.

    4. Read the value displayed on the GTS.

      OK
      Tester Display Condition Specified Condition
      Accel Sens. No. 1 Volt %

      Accelerator Pedal

      Released → Depressed → Released

      		 Values smoothly change following accelerator pedal operation
      Accel Sens. No. 2 Volt %
      Tip:

      For numerical values of Accel Sens. No. 1 Volt % and Accel Sens. No. 2 Volt %, refer to the Data List (Click here).


  5. Click here

    READ VALUE USING GTS (VEHICLE SPEED)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Start the engine.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.

    5. Read the value displayed on the GTS.

      Standard
      Tester Display Condition Specified Condition
      Vehicle Speed Vehicle stopped, engine running 0 km/h (0 mph)
      Vehicle running at constant speed between 16.1 to 64.4 km/h (10 to 40 mph) No large fluctuations when driving at a constant speed
      CAUTION:

      When performing the confirmation driving pattern, obey all speed limits and traffic laws.

      Tip:

      Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.


  6. Click here

    END

  7. Click here

    GO TO VEHICLE SPEED SENSOR CIRCUITClick here

  8. Click here

    REPLACE ACCELERATOR PEDAL ROD ASSEMBLYClick here

  9. Click here

    REPAIR OR REPLACE BRAKE PEDALClick here

  10. Click here

    INSPECT STOP LIGHT SWITCH ASSEMBLYClick here

  11. Click here

    GO TO DTC CHART