Click here

REAR STABILIZER BAR (for 4WD) INSTALLATION

Click here
Click here
  1. Click here

    TEMPORARILY INSTALL REAR STABILIZER BAR


    1. A017E2UE01

      Temporarily install the rear stabilizer bar with the identification mark positioned on the left side of the vehicle.

  2. Click here

    TEMPORARILY INSTALL REAR STABILIZER BAR BRACKET LH (for Front Side)


    1. A017FU3

      Temporarily install the rear stabilizer bar bracket LH (front side) with the bolt.

      Tip:

      Loosely tighten the bolt so that the bracket can be moved by hand.

  3. Click here

    TEMPORARILY INSTALL REAR STABILIZER BAR BRACKET RH (for Front Side)


    1. A017EJX

      Temporarily install the rear stabilizer bar bracket RH (front side) with the 2 bolts.

      Tip:

      Loosely tighten the bolts so that the bracket can be moved by hand.

  4. Click here

    INSTALL REAR STABILIZER BUSHING (for LH Side)


    1. A017C0ZE01

      Install the rear stabilizer bushing (LH side) to the rear stabilizer bar.

      Note:

      Make sure that the cutout of the rear stabilizer bushing is positioned within the range shown in the illustration.

  5. Click here

    INSTALL REAR STABILIZER BUSHING (for RH Side)


    1. A017C9PE01

      Install the rear stabilizer bushing (RH side) to the rear stabilizer bar.

      Note:

      Make sure that the cutout of the rear stabilizer bushing is positioned within the range shown in the illustration.

  6. Click here

    INSTALL REAR STABILIZER BAR BRACKET LH (for Rear Side)


    1. A017DTY

      Install the rear stabilizer bar bracket LH (rear side) with the 2 bolts.

      19 N*m 194 kgf*cm 14 ft.*lbf
  7. Click here

    INSTALL REAR STABILIZER BAR BRACKET RH (for Rear Side)


    1. A017B8C

      Install the rear stabilizer bar bracket RH (rear side) with the 2 bolts.

      19 N*m 194 kgf*cm 14 ft.*lbf
  8. Click here

    FULLY TIGHTEN REAR STABILIZER BAR BRACKET LH (for Front Side)


    1. A017DTV

      Fully tighten the bolt.

      54 N*m 550 kgf*cm 40 ft.*lbf
  9. Click here

    FULLY TIGHTEN REAR STABILIZER BAR BRACKET RH (for Front Side)


    1. A017BT4

      Fully tighten the 2 bolts.

      19 N*m 194 kgf*cm 14 ft.*lbf
  10. Click here

    INSTALL REAR STABILIZER LINK ASSEMBLY LH


    1. A017FDCE02

      Install the rear stabilizer link assembly LH to the rear shock absorber with coil spring LH with the nut.

      39 N*m 400 kgf*cm 29 ft.*lbf
      Tip:

      If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud bolt.

    2. A017EW6E02

      Install the rear stabilizer link assembly LH to the rear stabilizer bar with the nut.

      39 N*m 400 kgf*cm 29 ft.*lbf
      Tip:

      If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud bolt.

  11. Click here

    INSTALL REAR STABILIZER LINK ASSEMBLY RH

    Tip:

    Perform the same procedure as the LH side.

  12. Click here

    INSTALL TAIL EXHAUST PIPE ASSEMBLY


    1. A017BDT

      Using vernier calipers, measure the free length of the compression spring.

      Minimum 40.5 mm (1.59 in.)
      Tip:

      If the length is less than the minimum, replace the compression spring.

    2. A017F8GE01

      Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the center exhaust pipe assembly.

      Note:

      • Tap in the gasket in the correct direction.

      • Do not reuse the removed gasket.

      • Do not push in the gasket while installing the tail exhaust pipe assembly.

    3. Connect the exhaust pipe support, and install the tail exhaust pipe assembly.

    4. A017DZ8

      Install the 2 compression springs and 2 bolts.

      48 N*m 489 kgf*cm 35 ft.*lbf
  13. Click here

    INSPECT FOR EXHAUST GAS LEAK

    If exhaust gas is leaking, repair the leak. Replace damaged or worn parts as necessary.

  14. Click here

    INSTALL REAR WHEELS

    103 N*m 1050 kgf*cm 76 ft.*lbf
  15. Click here

    INSTALL SPARE WHEEL CARRIER LOCK COVER

  16. Click here

    INSTALL SPARE TIRE

  17. Click here

    INSTALL LOWER SPARE WHEEL CARRIER HINGE COVER

  18. Click here

    INSTALL DECK TRIM SERVICE HOLE COVER

  19. Click here

    INSTALL REAR MAT


    1. A017F51

      Install the rear mat.

  20. Click here

    INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Install the tonneau cover assembly.

  21. Click here

    INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY (w/ Tonneau Cover)


    1. A017D36

      Engage the 2 guides and install the No. 2 deck board sub-assembly.

  22. Click here

    INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY (w/ Tonneau Cover)


    1. A017F31

      Engage the 2 guides and install the No. 3 deck board sub-assembly.

  23. Click here

    INSTALL DECK BOARD ASSEMBLY


    1. A017CPI

      Install the deck board sub-assembly.