Click here

FRONT LOWER SUSPENSION ARM INSTALLATION

Click here
Click here
Note:

When removing/installing the front lower suspension arm or related parts, make sure to inspect the suspension arm bolt as shown in the following procedure.

Click here
  1. Click here

    INSTALL FRONT LOWER SUSPENSION ARM


    1. Install the front lower arm bushing stopper to the front lower suspension arm.

    2. Install the front lower suspension arm to the front frame assembly with the 3 bolts and nut, but do not tighten them yet.

    3. A017E5UE01

      Measure the outer diameter of the washer on the bolt (3) indicated by *1 in the illustration. If the outer diameter is 32 mm (1.260 in.), replace the bolt with a type B bolt shown in the table below. If the washer outer diameter is 34 mm (1.338 in.), it is not necessary to replace the bolt.

      Bolt Part Number Washer Outer Diameter
      Type A 90119-14116 32 mm (1.260 in.)
      Type B 90119-14140 32 mm (1.260 in.)
      Type C 90119-14126 34 mm (1.338 in.)
      Note:

      • When removing/reinstalling the front lower suspension arm or related parts, make sure to inspect the bolt (3) in the illustration and , if necessary, replace it with a type B bolt shown in the above table.

      • There is no difference of the washer outer diameter between type A and B so that they cannot be visually distinguished.

      Tip:

      If a type B bolt was installed in an earlier procedure, it is not necessary to replace it.

    4. Tighten the 3 bolts in numerical order shown in the illustration.

      Bolt 1, 2
      200 N*m 2039 kgf*cm 147 ft.*lbf
      Bolt 3
      135 N*m 1377 kgf*cm 100 ft.*lbf
      Tip:

      Start installing the bolts from the front side of the vehicle.

  2. Click here

    INSTALL FRONT FRAME ASSEMBLY


    1. A017G59E01

      Temporarily install the engine assembly with transaxle with the 9 nuts and 2 bolts.

    2. A017EZT

      Tighten the bolt.

      87 N*m 887 kgf*cm 64 ft.*lbf
    3. A017B4F

      Tighten the 3 nuts.

      52 N*m 530 kgf*cm 38 ft.*lbf
    4. A017FY0E01

      Tighten the 4 nuts.

      A
      95 N*m 969 kgf*cm 70 ft.*lbf
      B
      87 N*m 888 kgf*cm 65 ft.*lbf
    5. A017BZWE01

      Tighten the 4 nuts.

      A
      95 N*m 969 kgf*cm 70 ft.*lbf
      B
      87 N*m 888 kgf*cm 65 ft.*lbf
    6. A017EAV

      Tighten the 2 bolts.

      78 N*m 795 kgf*cm 58 ft.*lbf
    7. A017EBR

      Connect the duty vacuum switching valve connector and clamp.

    8. A017DSBE01

      Install the 5 hole plugs.

  3. Click here

    REMOVE ENGINE HANGERS


    1. A017DNOE01

      Remove the 4 bolts and 2 engine hangers.

  4. Click here

    INSTALL POWER STEERING LINK ASSEMBLY


    1. A017BH9

      Install the power steering link assembly with the 2 bolts and 2 nuts.

      70 N*m 713 kgf*cm 51 ft.*lbf
      Note:

      • Make sure to tighten the bolts starting from the left side of the vehicle.

      • Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut fixed.

  5. Click here

    INSTALL FRONT STABILIZER BAR WITH FRONT STABILIZER LINK ASSEMBLY

  6. Click here

    INSTALL NO. 1 FRONT STABILIZER BRACKET LH


    1. A017DRG

      Install the No. 1 front stabilizer bracket LH to the front frame assembly with the 2 bolts.

      29 N*m 296 kgf*cm 21 ft.*lbf
  7. Click here

    INSTALL NO. 1 FRONT STABILIZER BRACKET RH

    Tip:

    Perform the same procedure as the LH side.

  8. Click here

    INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

    Tip:

    Install engine assembly with transaxle (Click here).