Click here

FRONT LOWER BALL JOINT INSTALLATION

Click here
Click here
  1. Click here

    INSTALL FRONT LOWER BALL JOINT


    1. A017EPM

      Install the front lower ball joint to the steering knuckle with the nut.

      123 N*m 1254 kgf*cm 91 ft.*lbf
      Note:

      Prevent oil from adhering to the screw and tapered parts.

    2. Install a new cotter pin.

      Note:

      If the holes for the cotter pin are not aligned, tighten the nut further up to 60°.

  2. Click here

    INSTALL FRONT AXLE ASSEMBLY


    1. A017BFY

      Install the front axle assembly to the front shock absorber with the 2 bolts and 2 nuts.

      290 N*m 2956 kgf*cm 213 ft.*lbf
  3. Click here

    INSTALL FRONT DRIVE SHAFT ASSEMBLY


    1. A017DYRE04

      Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly.

  4. Click here

    INSTALL FRONT LOWER SUSPENSION ARM


    1. A017CVO

      Install the front lower suspension arm to the front lower ball joint with the bolt and 2 nuts.

      92 N*m 938 kgf*cm 68 ft.*lbf
  5. Click here

    CONNECT TIE ROD ASSEMBLY


    1. Connect the tie rod assembly LH to the steering knuckle with the nut.

      49 N*m 500 kgf*cm 36 ft.*lbf

    2. Install a new cotter pin.

      Note:

      Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.

  6. Click here

    INSTALL FRONT DISC


    1. A017EY2E01

      Align the matchmarks and install the front disc.

      Note:

      When replacing the disc with a new one, select the installation position where the front disc has minimal runout.

  7. Click here

    INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY


    1. A017DGF

      Install the front disc brake caliper assembly to the steering knuckle with the 2 bolts.

      104 N*m 1060 kgf*cm 77 ft.*lbf
  8. Click here

    INSTALL FRONT SPEED SENSOR


    1. A017B3HE01

      Install the clamp and front speed sensor with the bolt.

      8.5 N*m 87 kgf*cm 75 in.*lbf
      Note:

      • Prevent foreign matter from attaching to the sensor tip.

      • Firmly insert the sensor body into the knuckle before tightening the bolt.

      • After installing the sensor to the knuckle, make sure that there is no clearance between the sensor stay and knuckle. Also make sure that no foreign matter is stuck between the parts.

      • To prevent interference between the sensor and magnetic rotor, do not rotate the sensor body during or after the insertion of the sensor body to the knuckle.

  9. Click here

    INSTALL FRONT AXLE HUB NUT


    1. Clean the threaded parts on the drive shaft and axle hub nut using a non-residue solvent.

      Tip:

      • Be sure to perform this work for a new drive shaft.

      • Keep the threaded parts free of oil and foreign objects.

    2. A017BCD

      Using a socket wrench (30 mm), install a new axle hub nut.

      294 N*m 2996 kgf*cm 216 ft.*lbf

    3. Using a chisel and hammer, stake the front axle hub nut.

  10. Click here

    CHECK ABS SPEED SENSOR SIGNAL

    Tip:

    Check ABS speed sensor signal (Click here).

  11. Click here

    INSTALL FRONT WHEEL

    103 N*m 1050 kgf*cm 76 ft.*lbf
  12. Click here

    INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

    Tip:

    Inspect and adjust front wheel alignment (Click here).