Click here

FRONT AXLE HUB REMOVAL

Click here
Click here
  1. Click here

    REMOVE FRONT WHEEL

  2. Click here

    REMOVE FRONT AXLE HUB NUT


    1. A017E4SE01

      Using SST and a hammer, release the staked part of the front axle hub nut.

      09930-00010
      Note:

      Loosen the staked part of the nut completely, otherwise the threads of the drive shaft may be damaged.

    2. While applying the brakes, remove the front axle hub nut.

  3. Click here

    SEPARATE FRONT SPEED SENSOR


    1. A017CELE03

      Remove the bolt and resin clamp, and separate the front speed sensor.

  4. Click here

    SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY


    1. A017DGF

      Remove the 2 bolts and separate the front disc brake caliper assembly.

      Note:

      Use wire or an equivalent tool to keep the front disc brake caliper assembly from hanging down by the flexible hose.

  5. Click here

    REMOVE FRONT DISC


    1. A017EY2E01

      Remove the front disc.

      Tip:

      Put matchmarks on the disc and the axle hub.

  6. Click here

    SEPARATE TIE ROD ASSEMBLY


    1. Remove the cotter pin and the nut.

    2. A017D20E01

      Install SST to the tie rod end.

      09960-20010 09961-02060
      Note:

      Make sure that the upper ends of the tie rod end and SST are aligned.

    3. A017D19E01

      Using SST, separate the tie rod end from the steering knuckle.

      09960-20010 09961-02010
      Note:

      • When securing SST to the steering knuckle, be sure to tighten the string of SST to prevent it from falling.


      • Install SST so that A and B are parallel.


      • Be sure to place the wrench on the part indicated in the illustration.


      • Do not damage the front disc brake dust cover.


      • Do not damage the ball joint dust cover.


      • Do not damage the steering knuckle.

  7. Click here

    SEPARATE FRONT LOWER SUSPENSION ARM


    1. A017CVO

      Remove the bolt and 2 nuts, and separate the front lower suspension arm from the front lower ball joint.

  8. Click here

    SEPARATE FRONT DRIVE SHAFT ASSEMBLY


    1. A017DYRE05

      Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.

      Note:

      Do not punch the marks.

    2. A017BEP

      Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.

      Note:

      Be careful not to damage the drive shaft boot and speed sensor rotor.

  9. Click here

    REMOVE FRONT AXLE ASSEMBLY


    1. A017F4JE01

      Remove the 2 bolts, 2 nuts and front axle assembly.

      Note:

      When removing the nuts, keep the bolts from rotating.

  10. Click here

    REMOVE FRONT LOWER BALL JOINT


    1. A017D1J

      Secure the front axle assembly in a vise using aluminum plates.

      Note:

      When using a vise, do not overtighten it.

    2. A017EPM

      Remove the cotter pin and nut.

    3. A017D26E02

      Install SST to the front lower ball joint as shown in the illustration.

      09960-20010 09961-02050 09961-02050
      Note:

      Check that the clearance measurement between SST and the front axle assembly is 1 mm (0.04 in.).

    4. A017EVPE01

      Using SST, remove the front lower ball joint from the front axle assembly as shown in the illustration.

      09960-20010 09961-02010 09961-02050 09961-02050
      Note:

      • Install SST so that A and B are parallel.

      • Be sure to place a wrench on the part indicated in the illustration.

      • Do not damage the front lower ball joint dust cover.

  11. Click here

    REMOVE NO. 1 FRONT WHEEL BEARING DUST DEFLECTOR


    1. A017CHME02

      Using a screwdriver with its tip wrapped with vinyl tape, remove the No. 1 front wheel bearing dust deflector.

      Note:

      Be careful not to damage the steering knuckle.

  12. Click here

    REMOVE FRONT AXLE HUB HOLE SNAP RING


    1. A017DRJ

      Using snap ring pliers, remove the front axle hub hole snap ring.

  13. Click here

    REMOVE FRONT AXLE HUB SUB-ASSEMBLY


    1. Hold the front axle assembly between aluminium plates in a vise.

      Note:

      Do not overtighten the vise.

    2. A017FR7E01

      Using SST, remove the front axle hub sub-assembly.

      09520-00031
    3. A017DP7E02

      Using SST and a press, remove the bearing inner race (outside) from the front axle hub sub-assembly.

      09555-55010
      09950-60010 09951-00430
      09950-70010 09951-07100
      Note:

      Be careful not to drop the front axle hub sub-assembly.

  14. Click here

    REMOVE FRONT DISC BRAKE DUST COVER


    1. A017DT4

      Remove the 4 bolts and front disc brake dust cover from the steering knuckle.

  15. Click here

    REMOVE FRONT AXLE HUB BEARING


    1. Place the bearing inner race (outside) on the front axle hub bearing.

    2. A017DBME01

      Using SST, V-blocks and a press, remove the front axle hub bearing from the steering knuckle.

      09950-60010 09951-00430 09952-06010
      09950-70010 09951-07100
      09950-60020 09951-00750
      Note:

      Keep the steering knuckle level.