REAR DIFFERENTIAL CARRIER ASSEMBLY REMOVAL

REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

1. 

   Depress the brake pedal and hold it.

2. Using a hexagon wrench (6 mm), loosen the cross groove joint set bolts 1/2 turn.

   Tip:

   Put a piece of cloth or equivalent into the inside of the universal joint cover so that the boot does not touch the inside of the universal joint cover.

3. 

   Place matchmarks on the rear propeller shaft and rear drive pinion flange sub-assembly.

4. Remove the 4 nuts, 4 bolts and 4 washers.

5. 

   Remove the 4 bolts and 4 adjusting shims.

6. 

   Using a brass bar and a hammer, remove the propeller shaft with center bearing shaft assembly.

7. 

   Insert SST into the transfer to prevent oil leakage.

   09325-20010

REMOVE TAIL EXHAUST PIPE ASSEMBLY

1. 

   Remove the 2 bolts and 2 compression springs.

2. Disconnect the exhaust pipe support and remove the tail exhaust pipe assembly.

3. Remove the gasket from the center exhaust pipe assembly.

REMOVE CENTER EXHAUST PIPE ASSEMBLY

1. 

   Remove the 2 bolts and 2 compression springs.

2. Disconnect the 3 exhaust pipe supports and remove the center exhaust pipe assembly.

3. Remove the gasket from the No. 3 exhaust pipe sub-assembly.

REMOVE REAR SPEED SENSOR LH

1. 

   Remove the bolt and separate the rear speed sensor from the rear axle carrier sub-assembly.

   Note:

   Keep the sensor tip and rear speed sensor installation hole free from foreign matter.

REMOVE REAR AXLE SHAFT NUT LH

1. 

   Using SST and a hammer, release the staked part of the rear axle shaft nut.

   09930-00010

   Note:

   Loosen the staked part of the nut completely, otherwise the threads of the drive shaft may be damaged.

2. While applying the brakes, remove the rear axle shaft nut.

REMOVE REAR DISC BRAKE CALIPER ASSEMBLY LH

1. 

   Remove the 2 bolts and separate the rear disc brake caliper assembly.

   Note:

   Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.

REMOVE REAR DISC (for LH Side)

1. 

   Put matchmarks on the rear disc and the axle hub.

2. 

   Release the parking brake and remove the rear disc.

   Tip:

   If the disc cannot be removed easily, turn and press firmly the shoe adjuster until the wheel comes free.

REMOVE REAR AXLE HUB AND BEARING ASSEMBLY LH

1. 

   Put matchmarks on the drive shaft and axle hub.

   Note:

   Do not punch the marks.

2. 

   Remove the 4 bolts and the rear axle hub and bearing assembly.

   Note:
   

   • Do not rotate the drive shaft with the rear axle hub and bearing assembly removed.

   • Use wire or an equivalent tool to keep the parking brake assembly from hanging down by the parking brake cable assembly.

REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY

1. 

   Remove the bolt and the nut, and separate the No. 3 parking brake cable assembly.

REMOVE REAR STRUT ROD ASSEMBLY (for LH Side)

1. 

   Remove the 2 bolts, the 2 nuts, and the rear strut rod assembly.

   Note:

   Since stopper nuts are used, loosen the bolts.

REMOVE REAR AXLE CARRIER SUB-ASSEMBLY LH

1. 

   Loosen the 2 bolts.

   Note:

   Since stopper nuts are used, loosen the bolts.

2. 

   Remove the 2 bolts and 2 nuts, and separate the rear shock absorber with coil spring (lower side) from the rear axle carrier sub-assembly.

   Note:
   

   • Be careful not to damage the outboard joint boot.

   • Be careful not to damage the speed sensor rotor.

3. 

   Remove the 2 bolts, the 2 nuts, and the rear axle carrier sub-assembly.

   Note:
   

   • Be careful not to damage the outboard joint boot.

   • Be careful not to damage the speed sensor rotor.

   Tip:

   Use wire or an equivalent tool to keep the rear drive shaft assembly from hanging down.

REMOVE REAR DRIVE SHAFT ASSEMBLY LH

1. 

   Using SST, remove the rear drive shaft assembly as shown in the illustration.

   09520-01010
   09520-24010	09520-32040

   Note:

   Remove the rear drive shaft assembly while keeping it level.

REMOVE REAR DRIVE SHAFT SNAP RING LH

1. 

   Using a screwdriver, remove the rear drive shaft snap ring.

REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY

1. 

   Support the rear suspension member with a jack using a wooden block.

   Tip:

   Use a properly sized wooden block to keep the jack and suspension member level.

2. 

   Remove the 4 nuts, 2 bolts and 2 rear lower suspension member stopper retainers.

3. Lower the rear suspension member.

4. Remove the 2 rear upper suspension member stoppers.