Click here

FRONT DRIVE SHAFT INSTALLATION

Click here
Click here
  1. Click here

    INSTALL FRONT DRIVE SHAFT ASSEMBLY LH


    1. A017CMX

      Align the shaft splines and install the drive shaft assembly LH with a brass bar and hammer.

      Note:

      • Set the shaft snap ring with the opening facing down.

      • Be careful not to damage the drive shaft dust cover, boot, or oil seal.

      • Move the drive shaft assembly while keeping it level.

  2. Click here

    INSTALL FRONT DRIVE SHAFT ASSEMBLY RH (for 2WD)


    1. Install the front drive shaft assembly RH.

    2. A017DJR

      Install a new bearing bracket hole snap ring and bolt.

      32 N*m 330 kgf*cm 24 ft.*lbf
      Note:

      • Do not damage the boot or oil seal.

      • Move the drive shaft assembly while keeping it level.

  3. Click here

    INSTALL FRONT DRIVE SHAFT ASSEMBLY RH (for 4WD)

    Tip:

    Perform the same procedure as for the LH side.

  4. Click here

    INSTALL FRONT AXLE ASSEMBLY LH


    1. A017DYRE05

      Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly.

  5. Click here

    INSTALL NO. 1 FRONT SUSPENSION LOWER ARM LH


    1. A017EOV

      Install the No. 1 front suspension lower arm to the front lower ball joint with the bolt and 2 nuts.

      92 N*m 938 kgf*cm 68 ft.*lbf
  6. Click here

    CONNECT TIE ROD ASSEMBLY LH


    1. Connect the tie rod assembly LH to the steering knuckle with the nut.

      49 N*m 500 kgf*cm 36 ft.*lbf

    2. Install a new cotter pin.

      Note:

      Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.

  7. Click here

    INSTALL FRONT SPEED SENSOR LH


    1. A017CELE03

      Install the resin clamp and front speed sensor with the bolt.

      8.0 N*m 82 kgf*cm 71 in.*lbf
      Note:

      • Prevent foreign matter from attaching to the sensor tip.

      • Firmly insert the sensor body into the knuckle before tightening the bolt.

      • After installing the sensor to the knuckle, make sure that there is no clearance between the sensor stay and knuckle. Also make sure that no foreign matter is stuck between the parts.

      • To prevent interference between the sensor and magnetic rotor, do not rotate the sensor body during or after the insertion of the sensor body to the knuckle.

  8. Click here

    INSTALL FRONT STABILIZER LINK ASSEMBLY LH


    1. A017CL5

      Install the front stabilizer link assembly to the front shock absorber with the nut.

      74 N*m 755 kgf*cm 55 ft.*lbf
      Note:

      If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud bolt.

  9. Click here

    INSTALL FRONT AXLE HUB NUT LH


    1. Clean the threaded parts on the drive shaft and axle hub nut using a non-residue solvent.

      Tip:

      • Be sure to perform this work for a new drive shaft.

      • Keep the threaded parts free of oil and foreign objects.

    2. A017BCD

      Using a socket wrench (30 mm), install a new axle hub nut.

      294 N*m 2996 kgf*cm 216 ft.*lbf

    3. Using a chisel and hammer, stake the front axle hub nut.

  10. Click here

    INSTALL FRONT WHEELS

    103 N*m 1050 kgf*cm 76 ft.*lbf
  11. Click here

    ADD AUTOMATIC TRANSAXLE FLUID

  12. Click here

    CHECK AUTOMATIC TRANSAXLE FLUID

    Tip:

    Drive the vehicle so that the engine and transaxle are at normal operating temperature.

    Fluid temperature
    70 to 80°C (158 to 176°F)

    1. Park the vehicle on a level surface and set the parking brake.

    2. A017FXGE05

      With the engine idling and the brake pedal depressed, move the shift lever to all positions from P to S1 and return to the P position.

    3. Take out the dipstick and wipe it clean.

    4. Put the dipstick back all the way.

    5. Take out the dipstick again and check that the fluid level is within the HOT range.

      If the fluid level is below the HOT range, add new fluid and recheck the fluid level.

      If the fluid level exceeds the HOT range, drain the fluid once, add the proper amount of new fluid and recheck the fluid level.

      If there are leaks, it is necessary to repair or replace O-rings, FIPGs, oil seals, plugs and/or other parts.

  13. Click here

    INSTALL TRANSFER DRAIN PLUG (for 4WD)


    1. A017ETHE05

      Install the transfer drain plug with a new drain gasket.

      49 N*m 500 kgf*cm 36 ft.*lbf
  14. Click here

    INSTALL NO. 1 TRANSFER CASE PLUG (for 4WD)


    1. Add oil up to 0 to 5 mm below the lower side of the plug hole.

      Oil quantity
      0.9 liters (0.95 US qts, 0.79 lmp.qts)
      Tip:

      When adding oil, pour it slowly.

    2. Install the No. 1 transfer case plug with a new No. 1 gasket.

      49 N*m 500 kgf*cm 36 ft.*lbf
  15. Click here

    CHECK TRANSFER OIL (for 4WD)


    1. A017BX2E03

      Remove the No. 1 transfer case plug and gasket.

    2. Check the oil level is within 0 to 5 mm (0 to 0.20 in.) below the lowest end of the hole for the No. 1 transfer case plug.

      Note:

      • When changing oil, recheck the oil level after driving.

      • Excessively large or small quantity of oil may cause some trouble.

    3. When the oil level is too low, check for oil leakage.

    4. Tighten the No. 1 transfer case plug with a new gasket.

      49 N*m 500 kgf*cm 36 ft.*lbf
  16. Click here

    INSTALL NO. 2 ENGINE UNDER COVER


    1. A017CNJ

      Install the No. 2 engine under cover with the 2 bolts.

  17. Click here

    INSTALL NO. 1 ENGINE UNDER COVER


    1. A017B8T

      Install the No. 1 engine under cover with the 6 bolts and 2 clips.

  18. Click here

    INSTALL ENGINE UNDER COVER ASSEMBLY


    1. A017FXN

      Install the engine under cover assembly with the 2 bolts, 2 screws and 5 clips.

    2. A017FPR

      Install the engine under cover assembly RR with the 2 bolts.

  19. Click here

    ADJUST FRONT WHEEL ALIGNMENT

    Tip:

    (Click here)

  20. Click here

    CHECK ABS SPEED SENSOR SIGNAL

    Tip:

    (Click here)