Click here

FRONT DRIVE SHAFT DISASSEMBLY

Click here
Click here
  1. Click here

    REMOVE FRONT DRIVE SHAFT HOLE SNAP RING


    1. A017BTQE04

      Using a screwdriver, remove the front drive shaft hole snap ring.

  2. Click here

    REMOVE NO. 2 FRONT AXLE INBOARD JOINT BOOT CLAMP


    1. A017EWI

      Using pliers, remove the No. 2 front axle inboard joint boot clamp as shown in the illustration.

  3. Click here

    REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP


    1. Remove the front axle inboard joint boot clamp.

      Tip:

      Perform the same procedures as for the No. 2 front axle inboard joint boot clamp.

  4. Click here

    SEPARATE FRONT AXLE INBOARD JOINT BOOT


    1. Separate the front axle inboard joint boot from the inboard joint assembly.

  5. Click here

    REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY


    1. Remove the grease from the inboard joint assembly.

    2. A017FJ8E12

      Put matchmarks on the inboard joint assembly and outboard joint shaft.

      Note:

      Do not use a punch for the marks.

    3. Remove the inboard joint assembly from the outboard joint shaft.

    4. A017BTX

      Using a snap ring expander, remove the shaft snap ring.

    5. A017C3SE05

      Put matchmarks on the outboard joint shaft and tripod joint.

      Note:

      Do not use a punch for the marks.

    6. Using a brass bar and a hammer, remove the tripod joint from the outboard joint shaft.

      Note:

      Do not tap the roller.

  6. Click here

    REMOVE FRONT AXLE INBOARD JOINT BOOT


    1. Remove the inboard joint boot from the outboard joint shaft.

  7. Click here

    REMOVE FRONT DRIVE SHAFT DAMPER


    1. A017C5N

      Using pliers, remove the drive shaft damper clamp as shown in the illustration.

    2. Remove the drive shaft damper.

  8. Click here

    REMOVE NO. 2 FRONT AXLE OUTBOARD JOINT BOOT CLAMP


    1. A017FA1E02

      Using pliers, remove the No. 2 front axle outboard joint boot clamp as shown in the illustration.

  9. Click here

    REMOVE FRONT AXLE OUTBOARD JOINT BOOT CLAMP


    1. Remove the front axle outboard joint boot clamp.

      Tip:

      Perform the same procedures as for the No. 2 front axle outboard joint boot clamp.

  10. Click here

    REMOVE FRONT AXLE OUTBOARD JOINT BOOT


    1. Remove the outboard joint boot from the outboard joint shaft.

    2. Remove the grease from the outboard joint.

  11. Click here

    REMOVE FRONT DRIVE SHAFT DUST COVER LH


    1. A017C75E07

      Using SST and a press, remove the drive shaft dust cover LH.

      09950-00020
      Note:

      Be careful not to drop the inboard joint assembly.

  12. Click here

    REMOVE FRONT DRIVE SHAFT DUST COVER RH (for 2WD RH Side)


    1. A017G4UE02

      Using a press, remove the drive shaft dust cover RH.

  13. Click here

    REMOVE FRONT DRIVE SHAFT DUST COVER RH (for 4WD RH Side)

    Tip:

    Perform the same procedure as for the LH side.

  14. Click here

    REMOVE FRONT DRIVE SHAFT DUST COVER (for 2WD RH Side)


    1. A017DQ7E03

      Using SST and a press, remove the drive shaft dust cover.

      09950-00020
  15. Click here

    REMOVE SIDE GEAR SHAFT HOLDER BEARING (for 2WD RH Side)


    1. A017CVFE04

      Using a snap ring expander, remove the drive shaft hole snap ring.

    2. A017EL8E04

      Using SST and a press, remove the bearing.

      09527-10011

    3. Remove the bearing bracket hole snap ring.

      Note:

      Be careful not to drop the inboard joint assembly.