SPEED SENSOR INSTALLATION


  1. INSTALL SPEED SENSOR (NC SENSOR)


    1. A017ETA

      Coat a new O-ring with ATF.

    2. Install the speed sensor with the bolt.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

      Tech Tips

      Make sure to install the same manufacturer's sensor.

    3. Connect the speed sensor connector.

  2. INSTALL SPEED SENSOR (NT SENSOR)


    1. A017GC2

      Coat a new O-ring with ATF.

    2. Install the speed sensor with the bolt.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

      Tech Tips

      Make sure to install the same manufacturer's sensor.

    3. Connect the speed sensor connector.

  3. INSTALL AIR CLEANER BRACKET


    1. A017BE8

      Install the 2 bolts and air cleaner bracket.

      Torque:
      12 N*m  { 123 kgf*cm, 9 ft.*lbf }

  4. INSTALL AIR CLEANER CASE SUB-ASSEMBLY


    1. A017BI0

      Install the air cleaner case with the 3 bolts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

    2. Connect the hose and connector.

  5. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

  6. INSTALL AIR CLEANER CAP SUB-ASSEMBLY


    1. A017DHBE01

      Install the air cleaner filter element, align the groove on the air cleaner hose with the throttle body alignment tab and tighten the clamp as shown in the illustration.

      Tech Tips


      • A = 30°

      • B = 11 to 14 mm (0.433 in. to 0.551 in.)

    2. Install the air cleaner cap with the 2 bolts and clips.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }
    3. A017BB9

      Connect the 3 vacuum hoses.

    4. A017EEU

      Connect the mass air flow meter connector.

    5. Connect the No. 2 ventilation hose and fuel vapor feed hose assembly.

  7. INSTALL NO. 1 AIR CLEANER INLET


    1. A017C2QE01

      Install the No. 1 air cleaner inlet with the 2 bolts.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf, [A] }
      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf, [B] }

    2. Connect the 2 vacuum hoses.

  8. INSTALL NO. 2 AIR CLEANER INLET


    1. A017D82

      Install the No. 2 air cleaner inlet with the 2 bolts.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

    2. Connect the 2 vacuum hoses and harness clamps.

  9. REMOVE COOL AIR INTAKE DUCT SEAL


    1. A017CN1

      Install the cool air intake duct seal with the 11 clips.

  10. INSTALL BATTERY


    1. A017ETJE01

      Install the battery tray and battery.

    2. Install the battery clamp with the bolt and nut.

      Torque:
      Bolt
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }
      Nut A
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }
      Nut B
      13 N*m  { 131 kgf*cm, 9 ft.*lbf }
      Nut C
      6.4 N*m  { 64 kgf*cm, 57 in.*lbf }

    3. Install the positive battery terminal and nut.

    4. Connect the negative battery terminal, and tighten the nut.

  11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.