Click here

AUTOMATIC TRANSAXLE SYSTEM, Diagnostic DTC:P2714

Click here
Click here
DTC Code DTC Name
P2714 Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT)
Click here

SYSTEM DESCRIPTION

The linear solenoid valve (SLT) controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and the vehicle speed sensor. The ECM adjusts the duty ratio (*) of the SLT solenoid valve to control hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.

(*): Duty Ratio

The duty ratio is the ratio of the period of continuity in one cycle. For example, if A is the period of continuity in one cycle, and B is the period of non-continuity, then

Duty Ratio=A/(A+B) x 100(%)

DTC No. DTC Detection Condition Trouble Area
P2714 ECM detects a malfunction on SLT (ON side) according to the revolution difference of the turbine, intermediate and the output shaft, and also by the oil pressure. (2-trip detection logic)

  • Shift solenoid valve SLT remains closed

  • Valve body is blocked

  • Torque converter clutch

  • Automatic transaxle (clutch, brake or gear, etc.)
Click here

MONITOR DESCRIPTION

In any forward position, when the difference between the revolutions of the turbine, Intermediate and output shaft exceeds the specified value (varies with Intermediate, output speed) determined by the ECM, the ECM illuminates the MIL and outputs the DTC.

When shift solenoid valve SLT remains on, the oil pressure goes down and the clutch engagement force decreases.

Note:

If you continue driving under these conditions, the clutch will burn out and the vehicle will no longer be drivable.

Click here

INSPECTION PROCEDURE

Click here

PROCEDURE


  1. Click here

    CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P2714)


    1. Connect Intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG) and turn the Intelligent tester main switch ON.

    3. When you use Intelligent tester:

      Select the item "Powertrain / Engine and ECT / DTC / Current or Pending".

    4. Read the DTCs using Intelligent tester.

      Result
      Result Proceed to
      P2714 A
      P2714 and other DTCs B
      Tip:

      If any other codes besides "P2714" are output, perform the troubleshooting for those DTCs first.


  2. Click here

    INSPECT SHIFT SOLENOID VALVE SLT


    1. A017EGEE92

      Remove the shift solenoid valve SLT.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      1 - 2 20°C (68°F) 5.0 to 5.6 Ω

    3. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

      OK
      The solenoid makes an operating sound.

  3. Click here

    INSPECT TRANSMISSION VALVE BODY ASSEMBLY

    OK
    There are no foreign objects on each valve.

  4. Click here

    INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

    OK
    The torque converter clutch operates normally.

  5. Click here

    REPAIR OR REPLACE AUTOMATIC TRANSAXLE ASSEMBLYClick here

  6. Click here

    GO TO DTC CHARTClick here

  7. Click here

    REPLACE SHIFT SOLENOID VALVE SLTClick here

  8. Click here

    REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLYClick here

  9. Click here

    REPLACE TORQUE CONVERTER CLUTCH ASSEMBLYClick here