AUTOMATIC TRANSAXLE SYSTEM, Diagnostic DTC:P0771

DTC Code DTC Name
P0771 Shift Solenoid "E" Performance (Shift Solenoid Valve SR)

SYSTEM DESCRIPTION

The ECM uses signals from the vehicle speed sensor to detect the actual gear position (1st, 2nd, 3rd, 4th or 5th gear).

Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of the shift solenoid valves, valve body or automatic transaxle (clutch, brake or gear, etc.).

DTC No. DTC Detection Condition Trouble Area
P0771 The gear required by the ECM does not match the actual gear when driving (2-trip detection logic)

  • Shift solenoid valve SR remains open or closed

  • Valve body is blocked

  • Automatic transaxle (clutch, brake or gear, etc.)

MONITOR DESCRIPTION

The ECM commands gear shifts by turning the shift solenoid valves "ON/OFF". According to the input shaft revolution, intermediate (counter) shaft revolution and output shaft revolution, the ECM detects the actual gear position (1st, 2nd, 3rd, 4th or 5th gear position). When the gear position commanded by the ECM and the actual gear position are not the same, the ECM illuminates the MIL and stores the DTC.

INSPECTION PROCEDURE

Tech Tips

Using Intelligent tester to perform Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Test early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Test.


  1. PERFORM ACTIVE TEST


    1. Warm up the engine.

    2. Turn the ignition switch off.

    3. Connect Intelligent tester to the DLC3.

    4. Turn the ignition switch on (IG).

    5. Turn on the tester.

    6. Select the item "Powertrain / Engine and ECT / Active Test / Shift Status".

    7. According to the display on the tester, perform the "Active Test".

      Tech Tips

      While driving, the shift position can be forcibly changed with Intelligent tester.

      Comparing the shift position commanded by the Active Test with the actual shift position enables you to confirm the problem Click here.

      Tester Display Test Part Control Range Diagnostic Note
      Control the Shift Position

      [Test Details]

      Operate the shift solenoid valve and set each shift position by yourself.

      [Vehicle Condition]


      • IDL: ON

      • Less than 50 km/h (31 mph)

      [Others]


      • Press "→" button: Shift up

      • Press "←" button: Shift down

      		 1st/2nd/3rd/4th/5th Possible to check the operation of the shift solenoid valves.

      Tech Tips


      • This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.

      • The shift position commanded by the ECM is shown in the Data List / Shift Status display on Intelligent tester.

PROCEDURE


  1. CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0771)


    1. Connect Intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG) and turn the Intelligent tester main switch ON.

    3. When you use Intelligent tester:

      Select the item "Powertrain / Engine and ECT / DTC / Current or Pending".

    4. Read the DTCs using Intelligent tester.

      Result
      Result Proceed to
      P0771 A
      P0771 and other DTCs B

      Tech Tips

      If any other codes besides "P0771" are output, perform the troubleshooting for those DTCs first.


    B

    GO TO DTC CHART Click here

    A

  2. INSPECT SHIFT SOLENOID VALVE (SR)


    1. A017FVDE07

      Remove the shift solenoid valve SR.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      Solenoid Connector (SR) - Solenoid Body (SR) 20°C (68°F) 11 to 15 Ω

    3. Connect positive (+) lead to the terminal of solenoid connector, negative (-) lead to the solenoid body.

      OK
      The solenoid makes an operating sound.

    NG

    REPLACE SHIFT SOLENOID VALVE (SR) Click here

    OK

  3. INSPECT TRANSMISSION VALVE BODY ASSEMBLY

    OK
    There are no foreign objects on each valve and they operate smoothly.

    NG

    REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY Click here

    OK

  4. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

    OK
    The torque converter clutch operates normally.

    NG

    REPLACE TORQUE CONVERTER CLUTCH ASSEMBLY Click here

    OK

    REPAIR OR REPLACE AUTOMATIC TRANSAXLE ASSEMBLY Click here